u-boot.git/drivers/power/Kconfig, branch v2016.07

sunxi: power: add AXP809 support

2016-05-25T15:52:39Z

The A80 uses the AXP809 as its primary PMIC. Signed-off-by: Chen-Yu Tsai Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: Implement poweroff support for axp818 pmic

2016-05-25T15:52:39Z

Adds poweroff support for axp818 pmic. Signed-off-by: Chen-Yu Tsai Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: power: axp818: Add support for switch SW

2016-05-25T15:52:39Z

The AXP818 has a switchable output, SW. This is commonly used for controlling power to the LCD backlight. Signed-off-by: Chen-Yu Tsai Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

power: axp818: Fix typo for fldo2 Kconfig description

2016-05-25T15:52:39Z

Description said eldo2 instead of fldo2, a copy-paste error. Fixes: 38491d9c6515 ("power: axp818: Add support for FLDOs") Signed-off-by: Chen-Yu Tsai Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: Add support for Allwinner A64 SoCs

2016-04-01T07:52:28Z

The Allwinner A64 SoC is used in the Pine64. This patch adds all bits necessary to compile U-Boot for it running in AArch64 mode. Unfortunately SPL is not ready yet due to legal problems, so we need to boot using the binary boot0 for now. Signed-off-by: Siarhei Siamashka [agraf: remove SPL code, move to AArch64] Signed-off-by: Alexander Graf Acked-by: Hans de Goede Signed-off-by: Hans de Goede

power: axp818: Add support for FLDOs

2016-03-31T15:03:58Z

The FLDOs on AXP818 PMIC normally provide power to CPUS and USB HSIC PHY on the A83T/H8. Signed-off-by: Chen-Yu Tsai Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

power: axp818: Fix DCDC5 default voltage

2016-03-31T15:03:56Z

DCDC5 is designed to supply VCC-DRAM, which is normally 1.5V for DDR3, 1.35V for DDR3L, and 1.2V for LPDDR3. Also remove CONFIG_AXP_DCDC5_VOLT from h8_homlet_v2_defconfig. Signed-off-by: Chen-Yu Tsai Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: power: add support for sy8106a driver

2016-02-23T19:50:07Z

SY8106A is a PMIC which is used on the Allwinner H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is implemented to set the default V-CPU voltage to 1200 mV. This driver is required to ensure the SY8106A V-CPU voltage is set to 1200 mV after a software reset. On cold boot the default SY8106A output voltage is selected to be 1200 mV by a pair of resistors on the Orange Pi PC and Plus. Signed-off-by: Jelle van der Waa Tested-by: Siarhei Siamashka Acked-by: Siarhei Siamashka Signed-off-by: Hans de Goede

sunxi: power: axp818: Enable support for ALDOs

2016-01-26T15:20:05Z

Previously, AXP818 ALDO support was partially added to Kconfig, but never enabled in the board file, nor properly set or configured in Kconfig. The boards continue to work because the AXP818 is designed to pair with the A83T/H8, and the default voltages match the reference design's requirements. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

power: axp818: Add support for DLDO and ELDO regulators

2016-01-26T15:20:05Z

AXP818 provides an array of LDOs to provide power to various peripherals. None of these regulators are critical. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede