Use CONFIG_$(PHASE_)DM_REGULATOR_PFUZE100 as the build condition for
pfuze100 regulator driver.
Add Kconfig option for SPL_DM_REGULATOR_PFUZE100.
To avoid break current platforms, set the Kconfig default value same
as PMIC_PFUZE100.

Signed-off-by: Peng Fan <peng.fan@nxp.com>

Some BUCKs could work in single/dual phase mode, not in independent
mode. In single/dual phase mode, registers of both regulators,
must be identically set. So configure mode and value for both BUCKs.

CONF registers are not touched, leave them as default OTP settings.

PFUZE100/200 SW3A/B, could work in single/dual phase mode, so introduce
a new macro by adding a pointer to the SW3B descriptor.

Signed-off-by: Peng Fan <peng.fan@nxp.com>

Some PFUZE regulators can operate in either low or high output voltage mode,
with different minimum voltages and voltage step sizes selected by a hardware
control bit. However, the current PFUZE100 regulator driver assumes low output
voltage mode only, resulting in incorrect voltage calculation and programming
when high voltage mode is enabled.

Extend the regulator descriptor to describe high output voltage mode by adding
a mask to detect the mode and a dedicated voltage description (min_uV and
step size). Update voltage get/set handling to dynamically select the correct
voltage parameters based on the high voltage mode bit.

Signed-off-by: Peng Fan <peng.fan@nxp.com>

regulator-min-microvolt in device tree is not always match the minimal
voltage in the pmic datasheet, direclty using the min value from device
tree as base may cause wrong voltage settings being written.

Directly use the min_uV from datasheet to avoid wrong settings.

Signed-off-by: Peng Fan <peng.fan@nxp.com>

Depending on the phase selection (single or multi), the FPWM bits
configured forces the regulator to operate in PWM mode. In case of
multi-phase selection, the FPWM_MP bits enforce the regulator to also
operate in multi-phase. This fixes correct multi-phase operation.

While at this, correct incorrect macro alignment as well.

Fixes: 065a452ae6a1 ("power: regulator: tps65941: add regulator support")
Link: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Takuma Fujiwara <t-fujiwara1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

Add the PM7550 regulator data found on Qualcomm Milos devices.
The tables are imported from the Linux driver (tag v7.0-rc4). The SMPS
regulators were not added now.

Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://patch.msgid.link/20260318-milos-bringup-v2-4-650b91dd75d8@fairphone.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

The DM_REGULATOR_QCOM_USB_VBUS functionality can only work with DM_PMIC
enabled as well, so express this dependency in Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Link: https://patch.msgid.link/20260323195302.2363577-1-trini@konsulko.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

Fix a missing closing quote in the error message when a regulator name
is not unique.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Julien Stephan <jstephan@baylibre.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>