u-boot.git/drivers/qe, branch v1.3.2

net: uec_phy: actually increment the timeout counter

2008-03-07T18:47:08+00:00

allow u-boot to recover (and, e.g., switch to another interface) in the
case where a PHY does not report autonegotiation is complete within its
two second timeout value.

Signed-off-by: Kim Phillips

fix QE firmware uploading limit

2008-03-03T21:10:11+00:00

Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.

Signed-off-by: Timur Tabi

net: uec_phy: handle 88e1111 rev.B2 erratum 5.6

2008-03-02T20:52:15+00:00

erratum 5.6 states the autoneg completion bit is functional only if the
autoneg bit is asserted.

This fixes any secondarily-issued networking commands on non-gigabit
links on the mpc8360 mds board.

Signed-off-by: Kim Phillips

QE: Move FDT support into a common file

2008-02-11T23:36:21+00:00

Move the flat device tree setup for QE related devices into
a common file shared between 83xx & 85xx platforms that have QE's.

Signed-off-by: Kumar Gala

Remove annoying debug printout for PHY less boards.

2008-01-16T21:56:57+00:00

PHY less board prints out lots of "read wrong ...":
read wrong value : mii_id 3,mii_reg 2, base e0102320
read wrong value : mii_id 3,mii_reg 3, base e0102320
UEC: PHY is Generic MII (ffffffff)
read wrong value : mii_id 3,mii_reg 4, base e0102320
read wrong value : mii_id 3,mii_reg 0, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
FSL UEC0: Full Duplex
FSL UEC0: Speed 100BT
FSL UEC0: Link is up
Using FSL UEC0 device

Make this printout depend on UEC_VERBOSE_DEBUG and
remove its definition in uec_phy.c

Signed-off-by: Joakim Tjernlund 
Signed-off-by: Ben Warren

net: reduce boot latency on QE UEC based boards

2008-01-16T21:54:20+00:00

actually polling for PHY autonegotiation to finish enables us to remove the
5 second boot prompt latency present on QE based boards.

call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from
uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait
code shamelessly stolen from tsec driver.

also rm unused CONFIG_RMII_MODE code.

Signed-off-by: Kim Phillips 
Signed-off-by: Joakim Tjernlund 
Signed-off-by: Ben Warren

QE UEC: Extend number of supported UECs to 4

2008-01-16T04:08:58+00:00

This patch extends the number of supported UECs to 4. Note that the
problem of QE thread resources exhaustion is resolved by setting the
correct number of QE threads according to Ethernet type (GBE or FE).

Signed-off-by: David Saada 
Signed-off-by: Ben Warren

QE: fix compile warning

2008-01-14T09:34:30+00:00

qe.c: In function 'qe_upload_firmware':
qe.c:390: warning: pointer targets in passing argument 2
uec.c: In function 'uec_initialize':
uec.c:1236: warning: 'uec_info' may be used uninitialized

Signed-off-by: Dave Liu

Fix Ethernet init() return codes

2008-01-10T00:06:02+00:00

Change return values of init() functions in all Ethernet drivers to conform
to the following:

    >=0: Success
    <0:  Failure

All drivers going forward should return 0 on success.  Current drivers that
return 1 on success were left as-is to minimize changes.

Signed-off-by: Ben Warren 
Acked-by: Stefan Roese 
Acked-by: Jean-Christophe PLAGNIOL-VILLARD 
Acked-by: Kim Phillips 
Acked-by: Haavard Skinnemoen 
Acked-By: Timur Tabi

Coding Style cleanup; update CHANGELOG

2008-01-09T23:55:14+00:00

Signed-off-by: Wolfgang Denk