u-boot.git/drivers/qe, branch v1.3.2-rc2

QE: Move FDT support into a common file

2008-02-11T23:36:21Z

Move the flat device tree setup for QE related devices into a common file shared between 83xx & 85xx platforms that have QE's. Signed-off-by: Kumar Gala

Remove annoying debug printout for PHY less boards.

2008-01-16T21:56:57Z

PHY less board prints out lots of "read wrong ...": read wrong value : mii_id 3,mii_reg 2, base e0102320 read wrong value : mii_id 3,mii_reg 3, base e0102320 UEC: PHY is Generic MII (ffffffff) read wrong value : mii_id 3,mii_reg 4, base e0102320 read wrong value : mii_id 3,mii_reg 0, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 FSL UEC0: Full Duplex FSL UEC0: Speed 100BT FSL UEC0: Link is up Using FSL UEC0 device Make this printout depend on UEC_VERBOSE_DEBUG and remove its definition in uec_phy.c Signed-off-by: Joakim Tjernlund Signed-off-by: Ben Warren

net: reduce boot latency on QE UEC based boards

2008-01-16T21:54:20Z

actually polling for PHY autonegotiation to finish enables us to remove the 5 second boot prompt latency present on QE based boards. call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait code shamelessly stolen from tsec driver. also rm unused CONFIG_RMII_MODE code. Signed-off-by: Kim Phillips Signed-off-by: Joakim Tjernlund Signed-off-by: Ben Warren

QE UEC: Extend number of supported UECs to 4

2008-01-16T04:08:58Z

This patch extends the number of supported UECs to 4. Note that the problem of QE thread resources exhaustion is resolved by setting the correct number of QE threads according to Ethernet type (GBE or FE). Signed-off-by: David Saada Signed-off-by: Ben Warren

QE: fix compile warning

2008-01-14T09:34:30Z

qe.c: In function 'qe_upload_firmware': qe.c:390: warning: pointer targets in passing argument 2 uec.c: In function 'uec_initialize': uec.c:1236: warning: 'uec_info' may be used uninitialized Signed-off-by: Dave Liu

Fix Ethernet init() return codes

2008-01-10T00:06:02Z

Change return values of init() functions in all Ethernet drivers to conform to the following: >=0: Success <0: Failure All drivers going forward should return 0 on success. Current drivers that return 1 on success were left as-is to minimize changes. Signed-off-by: Ben Warren Acked-by: Stefan Roese Acked-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Kim Phillips Acked-by: Haavard Skinnemoen Acked-By: Timur Tabi

Coding Style cleanup; update CHANGELOG

2008-01-09T23:55:14Z

Signed-off-by: Wolfgang Denk

85xx: add ability to upload QE firmware

2008-01-09T22:28:12Z

Define the layout of a binary blob that contains a QE firmware and instructions on how to upload it. Add function qe_upload_firmware() to parse the blob and perform the actual upload. Add command-line command "qe fw" to take a firmware blob in memory and upload it. Update ft_cpu_setup() on 85xx to create the 'firmware' device tree node if U-Boot has uploaded a firmware. Fully define 'struct rsp' in immap_qe.h to include the actual RISC Special Registers. Signed-off-by: Timur Tabi

Add support CONFIG_UEC_ETH3 in MPC83xx

2008-01-08T15:55:41Z

Signed-off-by: Joakim Tjernlund

Fix cases where DECLARE_GLOBAL_DATA_PTR was not declared as global

2007-09-15T18:48:41Z

Signed-off-by: Wolfgang Denk