u-boot.git/drivers/qe, branch v1.3.4-rc2

Big white-space cleanup.

2008-05-20T22:14:08Z

This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk

uec: add support for Broadcom BCM5481 Gigabit PHY

2008-03-26T00:16:46Z

This patch adds basic support for Broadcom BCM5481 PHY. RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is Peter Barada . Signed-off-by: Anton Vorontsov

uec: add support for RGMII_RXID interface mode

2008-03-26T00:16:46Z

PHY drivers will use it to setup software delay between RXD and RXC signals. Signed-off-by: Anton Vorontsov

uec: add support for gbit mii status readings

2008-03-26T00:16:45Z

Signed-off-by: Anton Vorontsov

net: uec_phy: actually increment the timeout counter

2008-03-07T18:47:08Z

allow u-boot to recover (and, e.g., switch to another interface) in the case where a PHY does not report autonegotiation is complete within its two second timeout value. Signed-off-by: Kim Phillips

fix QE firmware uploading limit

2008-03-03T21:10:11Z

Fix a typo in qe_upload_firmware() that prevented uploading firmware on systems with more than one RISC core. Signed-off-by: Timur Tabi

net: uec_phy: handle 88e1111 rev.B2 erratum 5.6

2008-03-02T20:52:15Z

erratum 5.6 states the autoneg completion bit is functional only if the autoneg bit is asserted. This fixes any secondarily-issued networking commands on non-gigabit links on the mpc8360 mds board. Signed-off-by: Kim Phillips

QE: Move FDT support into a common file

2008-02-11T23:36:21Z

Move the flat device tree setup for QE related devices into a common file shared between 83xx & 85xx platforms that have QE's. Signed-off-by: Kumar Gala

Remove annoying debug printout for PHY less boards.

2008-01-16T21:56:57Z

PHY less board prints out lots of "read wrong ...": read wrong value : mii_id 3,mii_reg 2, base e0102320 read wrong value : mii_id 3,mii_reg 3, base e0102320 UEC: PHY is Generic MII (ffffffff) read wrong value : mii_id 3,mii_reg 4, base e0102320 read wrong value : mii_id 3,mii_reg 0, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 FSL UEC0: Full Duplex FSL UEC0: Speed 100BT FSL UEC0: Link is up Using FSL UEC0 device Make this printout depend on UEC_VERBOSE_DEBUG and remove its definition in uec_phy.c Signed-off-by: Joakim Tjernlund Signed-off-by: Ben Warren

net: reduce boot latency on QE UEC based boards

2008-01-16T21:54:20Z

actually polling for PHY autonegotiation to finish enables us to remove the 5 second boot prompt latency present on QE based boards. call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait code shamelessly stolen from tsec driver. also rm unused CONFIG_RMII_MODE code. Signed-off-by: Kim Phillips Signed-off-by: Joakim Tjernlund Signed-off-by: Ben Warren