Add driver for AST2700 to initialize DRAM in SPL.

This patch also refactors the Kconfig dependency of
Aspeed DRAM drivers as some of them are shared among
the file structures of RV and ARM ISAs.

Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

Remove <common.h> from this driver directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

According to the PLL vendor, we should keep the PLL power on, so we
shouldn't toggle the power-down bit during PLL initialization.

Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>

At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks.  Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.

Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>

Adjust the following settings to get better timing and signal quality.

1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]

2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]

3. CLK/CA timing
- 0x1e6e01a8[31]

4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])

Note1: Both DDR-PHY and DDR controller have their own registers for DDR4
Mode Registers (MR0~MR6).  This patch introduces macros to synchronize
the MR value on both sides.

Note2: the waveform meansurement can be found in item #21 of Aspeed
AST26x0 Application note (AP note).

Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>

The condition "~data" in the if-statement is a typo.  The original
intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use
"data == 0" for instead.

Besides, the bit[1] of "phy_status" register is hardwired to
SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has
already done, remove the unnecessary checking of phy_status[1].

Fixes: fde93143469f ("ram: aspeed: Add AST2600 DRAM control support")
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>