u-boot.git/drivers/ram, branch v2020.07

sifive: fu540: add ddr driver

2020-06-04T01:44:08+00:00

Add driver for fu540 to support ddr initialization in SPL.
This driver is based on FSBL
(https://github.com/sifive/freedom-u540-c000-bootloader.git)

Signed-off-by: Pragnesh Patel 
Tested-by: Bin Meng

common: Drop linux/bitops.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop linux/delay.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop log.h from common header

2020-05-19T01:19:18+00:00

Move this header out of the common header.

Signed-off-by: Simon Glass

command: Remove the cmd_tbl_t typedef

2020-05-18T22:36:55+00:00

We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass

common: Drop init.h from common header

2020-05-18T21:33:33+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop net.h from common header

2020-05-18T21:33:31+00:00

Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass

ram: stm32mp1: Add support for multiple configs

2020-05-14T07:02:12+00:00

Add support for multiple DRAM configuration subnodes, while retaining
the support for a single flat DRAM configuration node. This is useful
on systems which can be manufactured in multiple configurations and
where the DRAM configuration can be determined at runtime.

The code is augmented by a function which can be overridden on board
level, allowing a match on the configuration node name, very much like
the fitImage configuration node name matching works. The default match
is on the single top-level DRAM configuration, if matching on subnodes
is required, then this board_stm32mp1_ddr_config_name_match() must be
overridden.

Signed-off-by: Marek Vasut 
Cc: Manivannan Sadhasivam 
Cc: Patrick Delaunay 
Cc: Patrice Chotard

configs: stm32mp1: replace STM32MP1_TRUSTED by TFABOOT

2020-04-15T07:08:37+00:00

Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a12150 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.

Signed-off-by: Patrick Delaunay 
Reviewed-by: Patrice Chotard

ram: stm32mp1: the property st, phy-cal becomes optional

2020-03-24T13:23:30+00:00

This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.

It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.

This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
  "st,phy-cal" is not present in device tree (default behavior when
  DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
  - cal=1 => use param phy.cal to initialize the PHY, built-in training
             is skipped
  - cal=0 => param phy.cal is absent, built-in training is used (default)

Signed-off-by: Patrick Delaunay 
Acked-by: Patrice Chotard