The T113-s4 SoC is using the same die as the T113-s3, but comes with
256MiB of co-packaged DRAM. Besides the doubled size, the DRAM chip
seems to be connected slightly differently, which requires to use a
different pin remapping.

Extend the DRAM initialisation code to add support for the T113-S4 aka
T113M4020DC0 by checking the SoC's CHIPID, which is stored in the first
word of the SID efuses.

Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Tested-by: John Watts <contact@jookia.org>
Reviewed-by: John Watts <contact@jookia.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Our last sync with the kernel was 5.1.

We are so out of sync now, that tracking the patches and backporting
them one by one makes little sense and it's going to take ages.

This is an attempt to sync up Makefiles to 6.1.
Unfortunately due to sheer amount of patches this is not easy to review,
but that's what we decided during a community call for the bump to 5.1,
so we are following the same guidelines here.

Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>a #rebased on -next

Fix typo for "unsupport" size and improve description to Unknown DDR size.

Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Replace numeric literal with SZ_8G consistent with other uses of types
from linux/types.h

Signed-off-by: E Shattow <e@freeshell.de>
Acked-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

16GB memory size is not addressable on StarFive JH-7110 SoC because the
DRAM uncached alias begins at +8GB offset from start of DRAM. The logic
for 16GB memory size is a fall-through to the default for an unknown size.
Let's drop this unnecessary 16GB memory size and rely on the case default.

Signed-off-by: E Shattow <e@freeshell.de>

Prepare v2025.10-rc3

In dbsc5_read_vref_training the arrays dvw_min_byte0_table and
dvw_min_byte1_table have 128 elements per channel. The variable
vref_stop_index is limited to be a maximum of 128. This means that the
index used to access the arrays must use a test of '< vref_stop_index'
rather than '<= vref_stop_index' in order to prevent out of bounds
accesses to the arrays.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

K3 Inline ECC mechanism can support up to 3 regions of inline ECC, add
this support for single controller.

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>

The existing approach does not account for interleaving in the DDRs when
setting up regions. There is support for MSMC to calculate the regions
for each DDR, so modify k3_ddrss_probe to set the regions accordingly
for multi-DDR systems.

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>

Add support for calculation of the protected regions for each DDR in
multi-DDR systems. Since MSMC is the parent node of the individual DDRs
as well as responsible for their interleaving, it only makes sense for
MSMC to contain the logic for dividing the regions.

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>