Replace instances of http://www.ti.com with https://www.ti.com

Signed-off-by: Nishanth Menon <nm@ti.com>

- add Amlogic A1 clock driver
- add Amlogic A1 reset support
- add USB Device support for Amlogic A1
- enable RNG on Amlogic A1 & Amlogic S4
- move Amlogic Secure Monitor to standalone driver

The commit 85dc58289238 ("firmware: scmi: prepare uclass to pass channel
reference") added an explicit parameter, channel, but it seems to make
the code complex.

Hiding this parameter will allow for adding a generic (protocol-agnostic)
helper function, i.e. for PROTOCOL_VERSION, in a later patch.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>

This patch adds reset support for the Amlogic A1 family.
We add the structure meson_reset_drvdata, which in the future
will allow this driver to be used for other families by declaring
only the correct parameters reg_count and level_offset.

Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>

This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h

Move this out of the common header and include it only where needed.

Signed-off-by: Simon Glass <sjg@chromium.org>

This patch add missing return value check for allocating the driver's
private data. -ENOMEM will be returned if malloc() fails.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

The behaviour of dev_read_addr_size() is surprising as it does not
handle #address-cells and #size-cells but instead hardcodes the values
based on sizeof(fdt_addr_t).

This is different from dev_read_addr_size_index() and
dev_read_addr_size_name() both of which do read the cell sizes from the
device tree.

Since dev_read_addr_size() is only used by a single driver and this
driver is broken when CONFIG_FDT_64BIT does not match the address size
in the device tree, fix the function to behave like all of the other
similarly named functions.  Drop the property name argument as the only
caller passes "reg" and this is the expected property name matching the
other similarly named functions.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>  # chromebook_jerry
Tested-by: Simon Glass <sjg@chromium.org>  # chromebook_bob

The current DT bindings for the rk3588 clock use a different ID than the
one that is supposed to be written to the hardware registers.
Thus, we cannot use directly the id provided in the phandle, but rather
use a lookup table to correctly setup the hardware.

This approach has been implemented already in Linux, by commit :
f1c506d152ff ("clk: rockchip: add clock controller for the RK3588")

Hence, implement a similar approach using the lookup table, and adapt
the existing reset driver to work with SoCs using lookup table.
The file rst-rk3588.c has been copied as much as possible from Linux.

Adapt the clk rk3588 driver as well to bind the reset driver with the
lookup table.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>

Fix line spacing aligment in bind function

Fixes: 760188c1aa5b ("rockchip: reset: support a (common) rockchip reset drivers")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

Add a DM reset driver for StarFive JH7110 SoC.

Note that the register base address of reset controller is the
same with the clock controller. Therefore, there is no device
tree node alone for reset driver.It binds device node in
the clock driver

Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>