u-boot.git/drivers/serial/Kconfig, branch v2017.07

powerpc, 8xx: move Serial driver to drivers/serial/

2017-07-08T19:56:04Z

At the same time, move to Kconfig Signed-off-by: Christophe Leroy

serial, kconfig: fix menutext

2017-06-23T14:38:09Z

fix menutext for the options SPL_DM_SERIAL and TPL_DM_SERIAL. Both have the same text as DM_SERIAL, which is confusing. Signed-off-by: Heiko Schocher Reviewed-by: Stefan Roese

serial: omap: Support debug UART

2017-05-12T02:21:27Z

Add debug UART functions to permit omap specific ns16550 to provide an early debug UART. This is mostly in common with DEBUG_UART_NS16550 except for Mode definition register which is required for selecting UART mode(16x auto-baud or 13x mode). Signed-off-by: Lokesh Vutla Reviewed-by: Simon Glass Reviewed-by: Tom Rini

serial: add serial driver for BCM6345

2017-05-10T14:16:09Z

It is based on linux/drivers/tty/serial/bcm63xx_uart.c Signed-off-by: Álvaro Fernández Rojas Reviewed-by: Simon Glass

sunxi: fix the default value of CONS_INDEX on non-A23/A33 SUN8I

2017-04-25T09:44:21Z

Only A23/A33 in SUN8I want a default value of CONS_INDEX of 5, for other chips the default value is 1 like other Allwinner SoCs. Fix this default value. The original wrong value has lead to wrong console on H3 Orange Pi boards. Fixes: 7095f8641863 ("sunxi: Convert CONS_INDEX to Kconfig") Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard

sunxi: Convert CONS_INDEX to Kconfig

2017-04-20T11:20:32Z

Convert the CONS_INDEX configuration to Kconfig. Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not needed anymore. Default value is 1 except for sun5i (equals 2) and sun8i (equals 5). Signed-off-by: Mylène Josserand [Maxime: Added a depends on ARCH_SUNXI to avoid build breakages] Signed-off-by: Maxime Ripard

serial: Add serial driver for Intel MID

2017-04-10T02:02:03Z

Add a specific serial driver for Intel MID platforms. It has special fractional divider which can be programmed via UART_PS, UART_MUL, and UART_DIV registers. The UART clock is calculated as UART clock = XTAL * UART_MUL / UART_DIV The baudrate is calculated as baud rate = UART clock / UART_PS / DLAB Initialize fractional divider correctly for Intel Edison platform. For backward compatibility we have to set initial DLAB value to 16 and speed to 115200 baud, where initial frequency is 29491200Hz, and XTAL frequency is 38.4MHz. Signed-off-by: Andy Shevchenko Reviewed-by: Simon Glass Reviewed-by: Kever Yang

dm: serial: Allow driver-model serial to be disabled for TPL

2017-04-05T20:36:59Z

Add separate enable/disable controls for driver-model serial. While this is generally enabled in SPL it may not be in TPL, since serial output can be obtained with the debug UART with minimal code size. Signed-off-by: Simon Glass

Kconfig: Migrate CONFIG_BAUDRATE

2017-03-19T18:48:37Z

Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini

STiH410: Add STi serial driver

2017-03-15T00:40:19Z

This patch adds support to ASC (asynchronous serial controller) driver, which is basically a standard serial driver. This IP is common across other STMicroelectronics SoCs Signed-off-by: Patrice Chotard Reviewed-by: Simon Glass