Pre-relocation we may not have a clock but it's usually been enabled for
us already, or worst case we will enable it after relocation. Erroring
out in this case will almost always cause U-Boot to hang pre-relocation
which is undesirable and may be hard to debug.

Link: https://patch.msgid.link/20260320-casey-qcom-rpmh-serial-fixes-v1-1-b81d05832eec@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

Teach the GENI UART driver to load firmware, similar to i2c.

This is primarily intended for non-debug UARTs, but since we don't
support using these as the console we abort probe for now.

Remove duplicated register macros that are in the common geni-se header.

Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-7-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>

Enable the serial engine clk in probe so that this driver can work on
platforms that don't already initialize the clk for this device before
this driver runs. This fixes a problem I see on Coreboot platforms like
Trogdor where the UART hardware isn't enabled by coreboot unless the
serial console build is used.

Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-6-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>

Qualcomm peripherals like UART, SPI, I2C, etc are all exposed under a
common GENI Serial Engine wrapper device. Replace the stub driver we use
for this currently with a full-on misc device and implement support for
loading peripheral firmware.

Each of the peripherals has it's own protocol-specific firmware, this is
stored on the internal storage of the device with a well-known partition
type GUID.

To support this, GENI will bind peripherals in two stages. First the
ones that already have firmware loaded (such as the serial port) are
bound in the typical way. But devices that require firmware loading are
deferred until EVT_LAST_STAGE_INIT. At this point we can be sure that
the storage device is available, so we load the firmware and then bind
and probe the remaining children.

Child devices are expected to determine if firmware loading is necessary
and call qcom_geni_load_firmware().

Since Linux currently doesn't support loading firmware (and firmware may
not be available), we probe all GENI peripherals to ensure that they
always load firmware if necessary.

Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-3-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>

The NULL check for priv in qcom_geni_serial_poll_bit serves no useful
prupose as too much other code surrounding it relies on priv being
valid. Remove the NULL check for priv and other related code.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250811-serial_msm_geni-v1-2-4499179491bc@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

In msm_serial_setbrg if the call to get_clk_div_rate fails then there
will not have been an assignment to clk_div which will lead to the call
to geni_serial_baud using an uninitialised value.
Check for an error from get_clk_div_rate and return an error code if so.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250811-serial_msm_geni-v1-1-4499179491bc@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

Remove <common.h> from this driver directory and when needed
add missing include files directly.

Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

When using OF_LIVE, the debug UART driver won't be probed if it's a
subnode of the geni-se-qup controller. Add a NOP driver for the
controller to correctly discover its child nodes.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>