This reverts commit 82f5279b0cd99a9163d34cfe926d0316d9dc0d37.

The build failure of k2*evm boards was fixed in a different way by
the previous commit.  It is nasty to patch generic drivers around
with #ifdef CONFIG_CLK just for the KeyStone's matter.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Support instatiation through device tree. Also parse the fsl,dte-mode
property to determine whether DTE mode shall be used.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

When calling clk_get_by_index(), fall back to the legacy method of
getting the clock if -ENOENT is returned.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>

The Armada 3700's UART is a simple serial port. It has a 32 bytes
Tx FIFO and a 64 bytes Rx FIFO integrated. This patch adds support
for this UART including the DEBUG UART functions for very early
debug output.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>

Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>

We cannot call on the CONFIG_CLK based clk_get_rate function unless
CONFIG_CLK is set.

Signed-off-by: Tom Rini <trini@konsulko.com>

Previously ns16550 compatible UARTs probed via device tree have needed
their device tree nodes to contain a clock-frequency property. An
alternative to this commonly used with Linux is to reference a clock via
a phandle. This patch allows U-Boot to support that, retrieving the
clock frequency by probing the appropriate clock device.

For example, a system might choose to provide the UART base clock as a
reference to a clock common to multiple devices:

  sys_clk: clock {
    compatible = "fixed-clock";
    #clock-cells = <0>;
    clock-frequency = <10000000>;
  };

  uart0: uart@10000000 {
    compatible = "ns16550a";
    reg = <0x10000000 0x1000>;
    clocks = <&sys_clk>;
  };

  uart1: uart@10000000 {
    compatible = "ns16550a";
    reg = <0x10001000 0x1000>;
    clocks = <&sys_clk>;
  };

This removes the need for the frequency information to be duplicated in
multiple nodes and allows the device tree to be more descriptive of the
system.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.

However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.

This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.

That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

This is very likely to be necessary for normal use cases.
Set its default to 'y' for shorter defconfig files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>