Add parameter description.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform.  As pb1x00 had no listed
maintainer I am assuming that it is also orphaned.  Remove this platform
and then remove the unused SoC support.

Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

In raw mode, handle ctrl-c as normal. This allows normal ctrl-c behavior
such as aborting a command that is timing out without completely
terminating the sandbox executable.

In [1], Simon disabled this.  His reason for it was that it interferes
with piping test scripts. Piping should be done in cooked mode, so this
change should still not interfere.

[1] commit 8969ea3e9f2db04a6b3675 ("sandbox: Disable Ctrl-C")

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Explanation from Simon Glass
"Private data is created when the device is probed and freed when the
device is removed.

Platform data is created when the device is bound, and survives
probe/remove cycles.

Strictly speaking, platform data should be used to hold the decoded
device tree properties. Private data should be used for run-time
things the device needs to keep track of."

Based on description the driver needs to be switch to use platdata
instead of priv.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add code to reset all reset signals as in serial DT node. A reset
property is an optional feature, so do not fail if a reset property is
not present.

If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

This commit adds Actions Semi OWL family UART support. This driver
relies on baudrate configured by primary bootloaders.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

In Linux, the clock rate of the UART is given by the clock driver.

If you try to follow that in U-Boot, you would end up with adding
more u-boot,dm-pre-reloc properties, and also the clock driver would
be too big for SPL, which is used for UniPhier ARMv7 platform.

The current solution is to add 'clock-frequency' property to the
UART nodes, but it does not exist in the DT files in Linux.  I do
not want to let DT diverge for U-Boot.

Check the SoC compatible and set the clock rate according to it.
This will be helpful to sync DT between Linux and U-Boot.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Just for making it shorter.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This function is used only inside this driver that's why should be
static.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This issue was found when OF_LIVE was enabled that there are scrambled
chars on the console like this:
Chip ID:	zu3eg
Watchdog: Started��j�   sdhci@ff160000: 0, sdhci@ff170000: 1
In:    serial@ff010000

I found a solution for this problem exactly the same as I found later in
serial_msm fixed by:
"serial: serial_msm: initialize uart only before relocation"
(sha1: 7e5ad796bcd65772a87da236ae21cd536ae3a4d2)

What it is happening is that output TX fifo still contains chars to be
sent and _uart_zynq_serial_init() resets TX fifo even in the middle of
transfer.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>