Pre-relocation we may not have a clock but it's usually been enabled for
us already, or worst case we will enable it after relocation. Erroring
out in this case will almost always cause U-Boot to hang pre-relocation
which is undesirable and may be hard to debug.

Link: https://patch.msgid.link/20260320-casey-qcom-rpmh-serial-fixes-v1-1-b81d05832eec@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

After years of developing the ADI ADSP platform, Timesys was purchased
by another company and is no longer contracted to maintain the platform.

Signed-off-by: Philip Molloy <philip.molloy@analog.com>
Reviewed-by: Greg Malysa <malysagreg@gmail.com>

Currently, atmel-usart does not respect CONFIG_DEBUG_UART_SKIP_INIT so
it will always configure the debug UART.

However, this is unwanted on platforms on which TF-A or some other firmware
has already configured the debug UART.

This will be used for Microchip LAN969x support, so simply return early if
CONFIG_DEBUG_UART_SKIP_INIT is set.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>

Microchip LAN969x will not include any arch specific clk.h nor hardware.h,
so in order to support it only include <asm/arch/clk.h> and
<asm/arch/hardware.h> when AT91 is selected.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>

Move the arch specific atmel_serial.h header from AT91 to the generic
include/dm/platform_data.

This will be used for support on Microchip LAN969x.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>

Add support for the Google Goldfish TTY serial device. This virtual
device is commonly used in QEMU virtual machines (such as the m68k
virt machine) and Android emulators.

The driver implements basic console output and input polling using the
Goldfish MMIO interface.

Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Yao Zi <me@ziyao.cc>
Tested-by: Daniel Palmer <daniel@0x0f.com>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <simon.glass@canonical.com>
Acked-by: Angelo Dureghello <angelo@kernel-space.org>

It is very limited and minimal, only implements putc/puts.
This minimal driver is intended to be used in SPL, and other
size-constrained situations.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
Link: https://patch.msgid.link/20251126-spl-gx-v5-3-6cbffb2451ca@postmarketos.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>

Add the compatible for Exynos8895 UART as described in upstream
devicetree bindings. This enables support for Exynos8895 and other
similar UART devices, such as Exynos7870. Other than that, the driver
works as-is.

Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

I have a hunch VPL_DM_SERIAL should not be selectable if VPL isn't set
as implied by the prefix. Additionally, still based on the prefix, I'm
assuming VPL_DM should be a dependency. Since VPL_DM can only be
selectable when VPL is enabled, only depend on VPL_DM.

This mirrors SPL_DM_SERIAL and TPL_DM_SERIAL so seems right to me.

Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Teach the GENI UART driver to load firmware, similar to i2c.

This is primarily intended for non-debug UARTs, but since we don't
support using these as the console we abort probe for now.

Remove duplicated register macros that are in the common geni-se header.

Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-7-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>