u-boot.git/drivers/spi, branch v2012.07 Unnamed repository; edit this file 'description' to name the repository. kw_spi: add weak functions board_spi_claim/release_bus 2012-07-07T12:07:32+00:00 Valentin Longchamp valentin.longchamp@keymile.com 2012-06-01T01:31:03+00:00 24934fea0c6248ac33ccf398dd1a86e0b9904eeb This allows a final, board specific, step in the claim/relase_bus function for the SPI controller, which may be needed for some hardware designs. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> 
This allows a final, board specific, step in the claim/relase_bus
function for the SPI controller, which may be needed for some hardware
designs.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
kw_spi: support spi_claim/release_bus functions 2012-07-07T12:07:32+00:00 Valentin Longchamp valentin.longchamp@keymile.com 2012-06-01T01:31:02+00:00 ac486e3ba16c37514d135c359f61ed6e32a2921d These two function nows ensure that the MPP is configured correctly for the SPI controller before any SPI access, and restore the initial configuration when the access is over. Since the used pins for the SPI controller can differ (2 possibilities for each signal), the used pins are configured with CONFIG_SYS_KW_SPI_MPP. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> 
These two function nows ensure that the MPP is configured correctly for
the SPI controller before any SPI access, and restore the initial
configuration when the access is over.

Since the used pins for the SPI controller can differ (2 possibilities
for each signal), the used pins are configured with CONFIG_SYS_KW_SPI_MPP.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
kw_spi: backup and reset the MPP of the chosen CS pin 2012-07-07T12:07:31+00:00 Valentin Longchamp valentin.longchamp@keymile.com 2012-06-01T01:31:01+00:00 ca880679dda63f8d58393526c7e3257f772ccabe This was not done before, and in the case of a shared pin (for MPP0 between NF_IO[2] and CSn) this could lead to problems. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> 
This was not done before, and in the case of a shared pin (for MPP0
between NF_IO[2] and CSn) this could lead to problems.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
spi: tegra2: rename tegra2_spi.* to tegra_spi.* 2012-07-07T12:07:20+00:00 Tom Warren twarren.nvidia@gmail.com 2012-05-22T07:33:47+00:00 edffa63d3d6e76991998789f9fcbaa483731ca65 In anticipation of Tegra3 support, start removing/renaming Tegra2-specific files. No functional changes (yet). Also updated copyright to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com> 
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.

Signed-off-by: Tom Warren <twarren@nvidia.com>
spi: Tegra2: Seaboard: fix UART corruption during SPI transactions 2012-07-07T12:07:17+00:00 Tom Warren twarren@nvidia.com 2012-05-15T21:32:40+00:00 078078cfa91f72331421e6f7a46938a58a9b21a7 Simon Glass's proposal to fix this on Seaboard was NAK'd, so I removed his NS16550 references and added a small delay before SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes and saw no corruption (crc's matched) and no spurious comm chars. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Jimmy Zhang <jimmzhang@nvidia.com> 
Simon Glass's proposal to fix this on Seaboard was NAK'd, so I
removed his NS16550 references and added a small delay before
SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes
and saw no corruption (crc's matched) and no spurious comm chars.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
spi: mxs: Allow other chip selects to work 2012-05-15T06:31:35+00:00 Fabio Estevam fabio.estevam@freescale.com 2012-04-23T08:30:50+00:00 148ca64f327a89ef77e84756f5d351af33e59b64 MXS SSP controller may have up to three chip selects per port: SS0, SS1 and SS2. Currently only SS0 is supported in the mxs_spi driver. Allow all the three chip select to work by selecting the desired one in bits 20 and 21 of the HW_SSP_CTRL0 register. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> 
MXS SSP controller may have up to three chip selects per port: SS0, SS1 and SS2.

Currently only SS0 is supported in the mxs_spi driver.

Allow all the three chip select to work by selecting the desired one
in bits 20 and 21 of the HW_SSP_CTRL0 register.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
spi: mxs: Introduce spi_cs_is_valid() 2012-05-15T06:31:35+00:00 Fabio Estevam fabio.estevam@freescale.com 2012-04-23T08:30:49+00:00 79cb14ab39f970b85204ab1b2f796b02bb65335d Introduce spi_cs_is_valid() for validating spi bus and chip select numbers. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org> 
Introduce spi_cs_is_valid() for validating spi bus and chip select numbers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-03-30T16:09:08+00:00 Wolfgang Denk wd@denx.de 2012-03-30T16:09:08+00:00 bc6f6c87b685bcdcd5bef522982d15209b6b9601 * 'master' of git://git.denx.de/u-boot-arm: (146 commits) arm: Use common .lds file where possible arm: add a common .lds link script arm: Remove unneeded setting of LDCSRIPT Define CPUDIR for the .lds link script arm: Remove zipitz2 link script Allow arch directory to contain .lds without requiring Makefile OMAP: Remove omap1610inn-based boards arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings board/ti/beagle/beagle.c: Fix build warnings sdrc.c: Fix typo in do_sdrc_init() for SPL tegra: i2c: Add I2C driver tegra: fdt: i2c: Add extra I2C bindings for U-Boot tegra: i2c: Select I2C ordering for Seaboard tegra: i2c: Enable I2C on Seaboard tegra: i2c: Select number of controllers for Tegra2 boards tegra: i2c: Initialise I2C on Nvidia boards tegra: Enhance clock support to handle 16-bit clock divisors fdt: Add function to allow aliases to refer to multiple nodes tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE tegra: fdt: Enable FDT support for Ventana tegra: fdt: Enable FDT support for Seaboard tegra: usb: Enable USB on Seaboard tegra: usb: Add common USB defines for tegra2 boards tegra: usb: Add USB support to nvidia boards arm: Check for valid FDT after console is up fdt: Avoid early panic() when there is no FDT present tegra: usb: Add support for Tegra USB peripheral tegra: fdt: Add function to return peripheral/clock ID usb: Add support for txfifo threshold tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard tegra: usb: fdt: Add additional device tree definitions for USB ports tegra: fdt: Add clock bindings for Tegra2 Seaboard tegra: fdt: Add clock bindings tegra: fdt: Add additional USB binding fdt: Add tegra-usb bindings file from linux fdt: Add staging area for device tree binding documentation tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel tegra: fdt: Add Tegra2x device tree file from kernel arm: fdt: Add skeleton device tree file from kernel fdt: Add basic support for decoding GPIO definitions fdt: Add functions to access phandles, arrays and bools fdt: Tidy up a few fdtdec problems fdt: Add tests for fdtdec fdt: Add fdtdec_find_aliases() to deal with alias nodes arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load net: fec_mxc: allow use with cache enabled net: force PKTALIGN to ARCH_DMA_MINALIGN i.MX28: Enable caches by default i.MX28: Make use of the bounce buffer i.MX28: Do data transfers via DMA in MMC driver MMC: Implement generic bounce buffer i.MX28: Add cache support to MXS NAND driver i.MX28: Add cache support into the APBH DMA driver ARM926EJS: Implement cache operations board/vpac270/onenand.c: Fix build errors nhk8815: fix build errors atmel-boards: add missing atmel_mci.h ARM: highbank: setup env from boot source register ARM: highbank: change env config to use nvram ARM: highbank: add reset support ARM: highbank: Add boot counter support ARM: highbank: change TEXT_BASE to 0x8000 ARM: highbank: fix us_to_tick calculation ARM: highbank: add missing get_tbclk ARM: highbank: fix warning for calxedaxgmac_initialize net: calxedaxgmac: fix build due to missing __aligned definition EXYNOS: Add structure for Exynos4 DMC EXYNOS: SMDK5250: Support all 4 UARTs ARM: fix s3c2410 timer code ARM: davinci: fixes for cam_enc_4xx board omap3_spi: receive transmit mode calimain, enbw_cmc: Fix typo in comments Davinci: ea20: use gpio framework to access gpios OMAP3: mt_ventoux: sets its own mtdparts OMAP3: mt_ventoux: updated timing for FPGA twl4030: fix potential power supply handling issues NAND: TI: fix warnings in omap_gpmc.c cam_enc_4xx: Rename 'images' to 'imgs' arm: Add Prep subcommand support to bootm OMAP3: twister: add support to boot Linux from SPL SPL: call cleanup_before_linux() before booting Linux OMAP3: SPL: do not call I2C init if no I2C is set. Add cache functions to SPL for armv7 devkit8000: Implement and activate direct OS boot omap/spl: change output of spl_parse_image_header omap-common/spl: Add linux boot to SPL devkit8000/spl: init GPMC for dm9000 in SPL omap-common: Add NAND SPL linux booting devkit8000: add config for spl command Add cmd_spl command mx53ard: Initialize return code with error mx53: Make PLL2 to be the parent of UART clock configs: imx: Use CONFIG_SF_DEFAULT_CS mx28evk: Provide default values for SPI bus and chip select USB: ehci-mx6: Add proper IO accessors mx6: Read silicon revision from register i.MX28: Drop __naked function from spl_mem_init mxs_spi: Return proper timeout error i.MX28: Make the stabilization delays shorter pmic_i2c: Return error in case of invalid pmic_i2c_tx_num mx6: Remove duplicate definition of ANATOP_BASE_ADDR mx6: Fix reset cause for Power On Reset case i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG i.MX28: Enable additional DRAM address bits mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment mx31: add "ARM11P power gating" to get_reset_cause mx31pdk: Fix CONFIG_SYS_MEMTEST_END efikamx: Fix CONFIG_SYS_MEMTEST_END mx53smd: Fix CONFIG_SYS_MEMTEST_END mx53evk: Fix CONFIG_SYS_MEMTEST_END mx51evk: Fix CONFIG_SYS_MEMTEST_END i.MX6: mx6qsabrelite: add ext2 support imximage: Remove overwriting of flash_offset IXP: Fix GPIO_INT_ACT_LOW_SET() IXP: Fix NAND build warning on PDNB3 and SCPU IXP: Move PDNB3 and SCPU from Makefile to boards.cfg IXP: Squash warnings in IXP NPE IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST} IXP: Make IXP buildable with arm-linux- toolchains Examples: Properly append LDFLAGS to LD command SPL: Enable YMODEM support on BeagleBone and AM335x EVM SPL: Add YMODEM over UART load support SPL: Add README.omap3 README: document more SPL config options spl.c: Use __noreturn decorator config.mk: Check for -fstack-usage support config.mk: Make cc-option create a file under include/generated ... 
* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
  arm: Use common .lds file where possible
  arm: add a common .lds link script
  arm: Remove unneeded setting of LDCSRIPT
  Define CPUDIR for the .lds link script
  arm: Remove zipitz2 link script
  Allow arch directory to contain .lds without requiring Makefile
  OMAP: Remove omap1610inn-based boards
  arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
  board/ti/beagle/beagle.c: Fix build warnings
  sdrc.c: Fix typo in do_sdrc_init() for SPL
  tegra: i2c: Add I2C driver
  tegra: fdt: i2c: Add extra I2C bindings for U-Boot
  tegra: i2c: Select I2C ordering for Seaboard
  tegra: i2c: Enable I2C on Seaboard
  tegra: i2c: Select number of controllers for Tegra2 boards
  tegra: i2c: Initialise I2C on Nvidia boards
  tegra: Enhance clock support to handle 16-bit clock divisors
  fdt: Add function to allow aliases to refer to multiple nodes
  tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE
  tegra: fdt: Enable FDT support for Ventana
  tegra: fdt: Enable FDT support for Seaboard
  tegra: usb: Enable USB on Seaboard
  tegra: usb: Add common USB defines for tegra2 boards
  tegra: usb: Add USB support to nvidia boards
  arm: Check for valid FDT after console is up
  fdt: Avoid early panic() when there is no FDT present
  tegra: usb: Add support for Tegra USB peripheral
  tegra: fdt: Add function to return peripheral/clock ID
  usb: Add support for txfifo threshold
  tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard
  tegra: usb: fdt: Add additional device tree definitions for USB ports
  tegra: fdt: Add clock bindings for Tegra2 Seaboard
  tegra: fdt: Add clock bindings
  tegra: fdt: Add additional USB binding
  fdt: Add tegra-usb bindings file from linux
  fdt: Add staging area for device tree binding documentation
  tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel
  tegra: fdt: Add Tegra2x device tree file from kernel
  arm: fdt: Add skeleton device tree file from kernel
  fdt: Add basic support for decoding GPIO definitions
  fdt: Add functions to access phandles, arrays and bools
  fdt: Tidy up a few fdtdec problems
  fdt: Add tests for fdtdec
  fdt: Add fdtdec_find_aliases() to deal with alias nodes
  arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load
  net: fec_mxc: allow use with cache enabled
  net: force PKTALIGN to ARCH_DMA_MINALIGN
  i.MX28: Enable caches by default
  i.MX28: Make use of the bounce buffer
  i.MX28: Do data transfers via DMA in MMC driver
  MMC: Implement generic bounce buffer
  i.MX28: Add cache support to MXS NAND driver
  i.MX28: Add cache support into the APBH DMA driver
  ARM926EJS: Implement cache operations
  board/vpac270/onenand.c: Fix build errors
  nhk8815: fix build errors
  atmel-boards: add missing atmel_mci.h
  ARM: highbank: setup env from boot source register
  ARM: highbank: change env config to use nvram
  ARM: highbank: add reset support
  ARM: highbank: Add boot counter support
  ARM: highbank: change TEXT_BASE to 0x8000
  ARM: highbank: fix us_to_tick calculation
  ARM: highbank: add missing get_tbclk
  ARM: highbank: fix warning for calxedaxgmac_initialize
  net: calxedaxgmac: fix build due to missing __aligned definition
  EXYNOS: Add structure for Exynos4 DMC
  EXYNOS: SMDK5250: Support all 4 UARTs
  ARM: fix s3c2410 timer code
  ARM: davinci: fixes for cam_enc_4xx board
  omap3_spi: receive transmit mode
  calimain, enbw_cmc: Fix typo in comments
  Davinci: ea20: use gpio framework to access gpios
  OMAP3: mt_ventoux: sets its own mtdparts
  OMAP3: mt_ventoux: updated timing for FPGA
  twl4030: fix potential power supply handling issues
  NAND: TI: fix warnings in omap_gpmc.c
  cam_enc_4xx: Rename 'images' to 'imgs'
  arm: Add Prep subcommand support to bootm
  OMAP3: twister: add support to boot Linux from SPL
  SPL: call cleanup_before_linux() before booting Linux
  OMAP3: SPL: do not call I2C init if no I2C is set.
  Add cache functions to SPL for armv7
  devkit8000: Implement and activate direct OS boot
  omap/spl: change output of spl_parse_image_header
  omap-common/spl: Add linux boot to SPL
  devkit8000/spl: init GPMC for dm9000 in SPL
  omap-common: Add NAND SPL linux booting
  devkit8000: add config for spl command
  Add cmd_spl command
  mx53ard: Initialize return code with error
  mx53: Make PLL2 to be the parent of UART clock
  configs: imx: Use CONFIG_SF_DEFAULT_CS
  mx28evk: Provide default values for SPI bus and chip select
  USB: ehci-mx6: Add proper IO accessors
  mx6: Read silicon revision from register
  i.MX28: Drop __naked function from spl_mem_init
  mxs_spi: Return proper timeout error
  i.MX28: Make the stabilization delays shorter
  pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
  mx6: Remove duplicate definition of ANATOP_BASE_ADDR
  mx6: Fix reset cause for Power On Reset case
  i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
  i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
  i.MX28: Enable additional DRAM address bits
  mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
  mx31: add "ARM11P power gating" to get_reset_cause
  mx31pdk: Fix CONFIG_SYS_MEMTEST_END
  efikamx: Fix CONFIG_SYS_MEMTEST_END
  mx53smd: Fix CONFIG_SYS_MEMTEST_END
  mx53evk: Fix CONFIG_SYS_MEMTEST_END
  mx51evk: Fix CONFIG_SYS_MEMTEST_END
  i.MX6: mx6qsabrelite: add ext2 support
  imximage: Remove overwriting of flash_offset
  IXP: Fix GPIO_INT_ACT_LOW_SET()
  IXP: Fix NAND build warning on PDNB3 and SCPU
  IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
  IXP: Squash warnings in IXP NPE
  IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
  IXP: Make IXP buildable with arm-linux- toolchains
  Examples: Properly append LDFLAGS to LD command
  SPL: Enable YMODEM support on BeagleBone and AM335x EVM
  SPL: Add YMODEM over UART load support
  SPL: Add README.omap3
  README: document more SPL config options
  spl.c: Use __noreturn decorator
  config.mk: Check for -fstack-usage support
  config.mk: Make cc-option create a file under include/generated
  ...
omap3_spi: receive transmit mode 2012-03-27T20:05:29+00:00 jacopo mondi j.mondi@voltaelectronics.com 2011-03-02T05:13:22+00:00 08b5ab073d4eb389ffd622f71094cf1c70253c00 Implementation of receive-transmit mode for omap3 MCSPI. Introduces full duplex communication, needed by some spi devices (such as enc28j60). Signed-off-by: jacopo mondi <mondi@cs.unibo.it> <j.mondi@voltaelectronics.com> 
Implementation of receive-transmit mode for
omap3 MCSPI.

Introduces full duplex communication, needed by
some spi devices (such as enc28j60).

Signed-off-by: jacopo mondi <mondi@cs.unibo.it> <j.mondi@voltaelectronics.com>
mxs_spi: Return proper timeout error 2012-03-27T07:41:16+00:00 Fabio Estevam festevam@gmail.com 2012-03-18T17:23:35+00:00 d9fb6a4c7e61d735eec2936a8dc3877f83e61d24 Instead of returning -1, it is preferred to return -ETIMEDOUT in case of timeouts. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> 
Instead of returning -1, it is preferred to return -ETIMEDOUT in case of timeouts.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>