Add additional param for reset cmd, which provides type of reset.

Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>

Prepare v2021.04-rc4

sysreset uclass driver provides an implementation of 'reset'
command using the sysreset_ APIs unconditionally. It also
supports the 'poweroff' command using the sysreset_ APIs,
but under a Kconfig option CONFIG_SYSRESET_CMD_POWEROFF.

Let's do the same for the 'reset' command, by introducing a
new Kconfig option CONFIG_SYSRESET_CMD_RESET, and set it to
on by default, to allow a board that don't have a sysreset
reset driver yet, but have a sysreset poweroff driver to
compile without any issue.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

Use a minimal error message to save space. Sort the header files while we
are here.

Signed-off-by: Simon Glass <sjg@chromium.org>

In our Python tests we expect to see the word "resetting". It may be
truncated if we reset before the serial console buffer is transferred.

Wait for 100 ms between the "resetting ..." message and the actual reset
like we do when powering off.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass <sjg@chromium.org>