Including <common.h> pulls in a lot of bloat.  What this driver needs
is BIT(), so replace it with <linux/bitops.h>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>

Collect runtime BUG/WARN into a self-contained header <linux/bug.h>
to make these macros easier to use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*().  U-Boot does not support them in a clean
way.  So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.

We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround.  Hence this
patch, to find the best home for all printk variants.  If you want to
use printk() and friends, please include <linux/printk.h>.  This header
is self-contained, and pulls in only a few headers.

When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards.  This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.

To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel".  (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.

The difference is the loglevel is build-time determined.  To save the
image size, lower priority pr_*() are compiled out.  I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.

I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>

Add UniPhier platform specific glue layer to support USB3 Host mode
on Synopsys DWC3 IP.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

We see the choice of USB_DWC3_HOST / _GADGET in drivers/usb/dwc3/Kconfig,
but we can not choose USB_DWC3_HOST unless USB_GADGET is defined.
This is strange.

Loosen the "depends on" and also move "select USB_GADGET_DUALSPEED" to
the correct place.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Merely using dma_alloc_coherent does not ensure that there is no stale
data left in the caches for the allocated DMA buffer (i.e. that the
affected cacheline may still be dirty).

The original code was doing the following (on AArch64, which
translates a 'flush' into a 'clean + invalidate'):
  # during initialisation:
      1. allocate buffers via memalign
      	 => buffers may still be modified (cached, dirty)
  # during interrupt processing
      2. clean + invalidate buffers
      	 => may commit stale data from a modified cacheline
      3. read from buffers

This could lead to garbage info being written to buffers before
reading them during even-processing.

To make the event processing more robust, we use the following sequence
for the cache-maintenance:
  # during initialisation:
      1. allocate buffers via memalign
      2. clean + invalidate buffers
      	 (we only need the 'invalidate' part, but dwc3_flush_cache()
	  always performs a 'clean + invalidate')
  # during interrupt processing
      3. read the buffers
      	 (we know these lines are not cached, due to the previous
	  invalidation and no other code touching them in-between)
      4. clean + invalidate buffers
      	 => writes back any modification we may have made during event
	    processing and ensures that the lines are not in the cache
	    the next time we enter interrupt processing

Note that with the original sequence, we observe reproducible
(depending on the cache state: i.e. running dhcp/usb start before will
upset caches to get us around this) issues in the event processing (a
fatal synchronous abort in dwc3_gadget_uboot_handle_interrupt on the
first time interrupt handling is invoked) when running USB mass
storage emulation on our RK3399-Q7 with data-caches on.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

The dwc3_flush_cache() call was declared and used inconsistently:
 * The declaration assumed 'int' for addresses (a potential issue
   when running in a LP64 memory model).
 * The invocation cast the address to 'long'.

This change ensures that both the declaration and usage of this
function consistently uses 'uintptr_t' for correct behaviour even
when the allocated buffers (to be flushed) reside outside of the
lower 32bits of memory.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Remove sys_proto.h inclusion which is not used by the driver.

Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.

Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

It is pointless to build gadget driver if USB_GADGET is disabled.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>