u-boot.git/drivers/usb/eth, branch v2014.01

drivers: usb: convert makefiles to Kbuild style

2013-10-31T17:25:38+00:00

Signed-off-by: Masahiro Yamada

usb:smsx95xx LED activity for USB net driver

2013-10-20T21:42:40+00:00

Add LED activity for SMSX95XX USB Ether driver.

Signed-off-by: “Suriyan Ramasami" 
Acked-by: Simon Glass

net: smsc95xx: Add support for another SMSC95xx variant

2013-08-19T17:34:18+00:00

This patch adds support for the SMSC9500 with product id 0x9900 which is
equipped in the "EXSYS USB 2.0" etherner USB adapter.

Tested on omap3_beagle.

Signed-off-by: Stefan Roese

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38+00:00

Signed-off-by: Wolfgang Denk 
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini

usb: add support for the USB Ethernet adapter D-Link DUB-E100 H/W Ver C1

2013-06-30T16:41:08+00:00

This trivial patch adds the definition of the vid/pid for the Ver C1 of the
USB Ethernet adapter D-Link DUB-E100.

Signed-off-by: Pierre Aubert 
CC: Marek Vasut

usb: asix: Move software resets to basic_init

2013-06-12T20:22:51+00:00

The ASIX driver calls a basic_init() function during get_info(), so that
not all initialization tasks need to be redone on every init().
Unfortunately, the most important one is still triggered too often: the
driver does a full port and MII reset on every asix_init(), requiring up
to several seconds to reestablish the link.

This patch confines that software reset into the asix_basic_init()
function so that it will only be executed once. This saves about a
second of boot time on systems using BOOTP.

Note: this patch was previously submitted many moons ago as:

   usb: usbeth: asix: Do a fast init if link already established

That patch seens to have been lost or forgotten, so this is a rebased
version. It is tested on snow with a Asix USB dongle (Cisco).

Signed-off-by: Julius Werner 
Signed-off-by: Simon Glass 
Reviewed-by: Simon Glass 
Reviewed-by: Vadim Bendebury

OMAP5: Enable USB Ethernet support with LAN9730

2013-05-14T19:37:58+00:00

Added the LAN9730 to list of supported devices. This chip is used
in the sEVM, uEVM and som5_evb. Tested on the som5_evb with dhcp
and ping.

Signed-off-by: Lubomir Popov

usb: usbeth: smsc95xx: remove EEPROM loaded check

2013-03-18T17:58:54+00:00

[port of Linux kernel commit bcd218be5aeb by Steve Glendinning]

The eeprom read & write commands currently check the E2P_CMD_LOADED_ bit is
set before allowing any operations.  This prevents any reading or writing
unless a correctly programmed EEPROM is installed.

Signed-off-by: Michael Spang 
Signed-off-by: Simon Glass 
Acked-by: Marek Vasut

usb: add support for multiple usb controllers

2012-10-15T18:54:00+00:00

Allows to initialize more than one USB controller at once.

v2: print message when controller stop fails

Signed-off-by: Lucas Stach 
Reviewed-by: Marek Vasut

net: asix: add AX88772B support

2012-09-26T17:36:31+00:00

Add AX88772B ID together with two fixes needed to make this work.

1. The packet length check has to be adjusted, as all ASIX chips
only use 11 bits to indicate the length. AX88772B uses the other
bits to indicate unrelated things, which cause the check to fail.
This fix is based on a fix for the Linux kernel by Marek Vasut.
Linux upstream commit: bca0beb9363f8487ac902931a50eb00180a2d14a

2. AX88772B provides several bulk endpoints. Only the first
IN/OUT endpoints work in the default configuration. So stop
enumeration after we found them to avoid overwriting the
endpoint config with a non-working one.

Signed-off-by: Lucas Stach 
Reviewed-by: Marek Vasut 
Acked-by: Marek Vasut 
Acked-by: Joe Hershberger