u-boot.git/drivers/usb/gadget/Makefile, branch v2017.09

spl: add serial download protocol (SDP) support

2017-08-23T08:41:58Z

Add USB serial download protocol support to SPL. If the SoC started in recovery mode the SPL will immediately switch to SDP and wait for further downloads/commands from the host side. Signed-off-by: Stefan Agner Reviewed-by: Stefano Babic Reviewed-by: Łukasz Majewski

usb: gadget: add SDP driver

2017-08-23T08:41:58Z

Add SDP (Serial Downloader Protocol) implementation for U-Boot. The protocol is used in NXP SoC's boot ROM and allows to download program images. Beside that, it can also be used to read/write registers and download complete Device Configuration Data (DCD) sets. This basic implementation supports downloading images with the imx header format reading and writing registers. Signed-off-by: Stefan Agner Reviewed-by: Łukasz Majewski

powerpc, 8xx: remove support for 8xx

2017-06-12T12:37:55Z

There was for long time no activity in the 8xx area. We need to go further and convert to Kconfig, but it turned out, nobody is interested anymore in 8xx, so remove it (with a heavy heart, knowing that I remove here the root of U-Boot). Signed-off-by: Heiko Schocher

spl: add USB Gadget config option

2016-11-29T00:49:49Z

Introduce USB Gadget config option. This allows to combine Makefile entries for SPL_USBETH_SUPPORT and SPL_DFU_SUPPORT. Signed-off-by: Stefan Agner Acked-by: Lukasz Majewski Tested-by: Ravi Babu

spl: dfu: move DFU Kconfig to SPL Kconfig

2016-11-29T00:49:49Z

The DFU Kconfig menu entries should be part of the SPL Kconfig file. Also avoid using the top level Makefile by moving the config dependent build artifacts to the driver/ and driver/usb/gadget/ Makfiles. With that, DFU can be built again in SPL if CONFIG_SPL_DFU_SUPPORT is enabled. Fixes: 6ad6102246d8 ("usb:gadget: Disallow DFU in SPL for now") Signed-off-by: Stefan Agner Reviewed-by: Simon Glass Acked-by: Lukasz Majewski

usb:gadget: Disallow DFU in SPL for now

2016-09-27T14:46:20Z

Previously, DFU was not built in for SPL and often disabled via the board config.h file, in the SPL build. By moving DFU to Kconfig we now need to move this logic to the Makefile to continue to allow boards to fit within their SPL size limit (until gcc 6 is more widespread and unused strings will be discarded). Signed-off-by: Tom Rini

usb: s3c-otg: Rename USB_GADGET_S3C_UDC_OTG* to USB_GADGET_DWC2_OTG*

2015-12-17T20:54:40Z

The s3c-otg IP block is in fact a DWC2 OTG one, so finally rename the config option to make it less misleading. No functional change, just a mechanical change done using the following script: git grep USB_GADGET_S3C_UDC_OTG | cut -d : -f 1 | sort -u | \ while read line ; do sed -i "s/USB_GADGET_S3C_UDC_OTG/USB_GADGET_DWC2_OTG/g" $line ; done Signed-off-by: Marek Vasut

usb: s3c-otg: Rename sources to dwc2_*c

2015-12-17T20:54:40Z

The driver is actually for the Designware DWC2 controller. This patch renames the local source files to dwc2_*c and adjusts the Makefile to use the new names. Signed-off-by: Marek Vasut

usb: gadget: at91_udc: add at91_udc into U-Boot

2015-09-11T07:35:40Z

add U-Boot specific changes to the at91_udc linux driver, so it works with U-Boot. Signed-off-by: Heiko Schocher

implement Fastboot via USB OTG on bcm28155_ap boards

2015-07-22T06:57:54Z

Signed-off-by: Jiandong Zheng Signed-off-by: Steve Rae