u-boot.git/drivers/usb/host/Kconfig, branch v2018.09

usb: xhci: zynqmp: Remove support for !DM_USB

2018-05-18T11:23:15Z

Switch to DM_USB was done and there is no need to keep !DM_USB code in tree. Signed-off-by: Michal Simek Reviewed-by: Simon Glass

usb: dwc3-of-simple: Add support for DRA7/AM57 platforms.

2018-04-21T16:38:56Z

Add the compatibility with "ti,dwc3" and enable it by default if DM_USB is enabled. Signed-off-by: Jean-Jacques Hiblot

usb: dwc3-of-simple: Fix dependencies

2018-04-21T16:38:56Z

This simple glue layer does not require CONFIG_MISC, but it does require CONFIG_DM_USB. Signed-off-by: Jean-Jacques Hiblot

usb: host: Add simple of glue driver for DWC3 USB Controllers integration

2018-04-11T15:22:07Z

This is a port of the dwc3-of-simple driver from Linux to enable/deassert clock and resets of a simple DWC3 Controller HW glue. Signed-off-by: Neil Armstrong

usb: dwc2: Allow selection of data buffer size

2018-03-17T02:15:18Z

If we use hardware with very small RAM (let's consider just a couple of hundreds of kB but not megabytes) it is not super convenient to lose 64kB for statically allocated bufer which most probably won't be used as big as it is. Typically we'll have much shorter data packages to excahnge and in the worst case longer packets will be split on separate transactions. For those corner-cases user will be able to set his buffer size of choice via USB_DWC2_BUFFER_SIZE option in menuconfig. By default we'll use 64 kB as it was hard-coeded before so existing users shouldn't be affected at all. Signed-off-by: Alexey Brodkin Cc: Marek Vasut

arm64: layerscape: Move CONFIG_HAS_FSL_DR_USB to Kconfig

2018-01-09T11:37:15Z

Rename to USB_EHCI_FSL, use Kconfig to select ehci accordingly. Signed-off-by: Ran Wang

usb: xhci: Add Renesas R-Car xHCI driver

2017-11-26T01:22:36Z

Add firmware V3, firmware loader and XHCI glue for the Renesas R-Car Gen3 SoCs XHCI controller. Thus far only the R-Car Gen3 R8A7795 ES2.0+ and R8A7796 are supported. Signed-off-by: Marek Vasut Cc: Nobuhiro Iwamatsu Cc: Bin Meng

usb: host: Move CONFIG_XHCI_FSL to Kconfig

2017-10-27T15:44:06Z

use Kconfig to select xhci accordingly. Signed-off-by: Ran Wang Reviewed-by: Bin Meng Reviewed-by: York Sun

usb: Drop the EHCI RCar Gen3

2017-10-03T23:50:43Z

Since we use EHCI generic driver on RCar Gen3 , this driver is useless. Remove it. Signed-off-by: Marek Vasut Cc: Nobuhiro Iwamatsu Acked-by: Nobuhiro Iwamatsu Signed-off-by: Nobuhiro Iwamatsu

usb: dwc3: Add dwc3 glue driver support for STi

2017-09-22T11:39:59Z

This patch adds the ST glue logic to manage the DWC3 HC on STiH407 SoC family. It configures the internal glue logic and syscfg registers. Part of this code been extracted from kernel.org driver (drivers/usb/dwc3/dwc3-st.c) Signed-off-by: Patrice Chotard Reviewed-by: Simon Glass