u-boot.git/drivers/usb/host, branch v2011.12-rc1

USB: EHCI: Allow EHCI post-powerup configuration in board files

2011-12-11T13:50:03Z

This patch allows USB to work on some hosts, which need additional frobing after the host was powered up via regular USB powerup sequence. Signed-off-by: Marek Vasut Cc: Stefano Babic Cc: Remy Bohmer Cc: Wolfgang Grandegger Cc: Jason Liu

USB: MX5: Add MX5 usb post-init callback

2011-12-11T13:49:43Z

This is useful for USB Transceivers init etc. Signed-off-by: Marek Vasut Cc: Stefano Babic Cc: Remy Bohmer Cc: Wolfgang Grandegger Cc: Jason Liu

USB: MX5: Abstract out mx51 USB pixmux configuration

2011-12-11T13:49:37Z

Signed-off-by: Marek Vasut Cc: Stefano Babic Cc: Remy Bohmer Cc: Wolfgang Grandegger Cc: Jason Liu

USB: MX5: add generic USB EHCI support for mx51 and mx53

2011-12-11T13:49:31Z

It's derived from ehci-mxc and uses the header files of the ehci-fsl interface. The callback board_ehci_hcd_init() has been introduced to allow for board-specific setup when USB is started. Signed-off-by: Wolfgang Grandegger CC: Stefano Babic CC: Remy Bohmer

ehci: speed up initialization

2011-12-11T13:42:57Z

According to EHCI specification v1.0, the controller should stabilize the power on a port at most 20 ms after the port power bit transition. So, we put this setting in the virtual descriptor corresponding field, (bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each controller initialization/enumeration. Signed-off-by: Vincent Palatin

USB: Add usb_event_poll() to get keyboards working with EHCI

2011-12-11T13:40:38Z

Signed-off-by: Marek Vasut Cc: Remy Bohmer

USB: Fix complaints about strict aliasing in OHCI-HCD

2011-12-11T13:40:38Z

Signed-off-by: Marek Vasut

drivers/usb/host/ehci-mxc.c: Fix GCC 4.6 warning

2011-12-09T09:34:53Z

Fix: ehci-mxc.c: In function 'ehci_hcd_init': ehci-mxc.c:113:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin

drivers/usb/host/sl811-hcd.c: Fix GCC 4.6 build warning

2011-12-01T23:14:21Z

Fix: sl811-hcd.c: In function 'sl811_rh_submit_urb': sl811-hcd.c:556:8: warning: variable 'wIndex' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk Cc: Remy Bohmer

Merge branch 'master' of git://git.denx.de/u-boot-arm

2011-11-16T19:24:41Z

* 'master' of git://git.denx.de/u-boot-arm: arm, davinci: add DAVINCI_MMC_CLKID arm, davinci_emac: fix driver bug if more then 3 PHYs are detected arm, davinci: da850/dm365 lowlevel cleanup omap5: Add omap5_evm board build support. omap4/5: Add support for booting with CH. omap5: emif: Add emif/ddr configurations required for omap5 evm omap5: clocks: Add clocks support for omap5 platform. omap5: Add minimal support for omap5430. omap: Checkpatch fixes omap4: make omap4 code common for future reuse GCC4.6: Squash warnings in onenand_base.c GCC4.6: Fix common/usb.c on xscale OneNAND: Add simple OneNAND SPL PXA: vpac270: Enable the new generic MMC driver PXA: Cleanup serial_pxa PXA: Drop csb226 and innokom boards (unmaintained) m28evk: Fix comment about the number of RAM banks mx31: Fix checkpatch warnings in generic.c mx31: Use proper IO accessor for GPR register mx31: Remove duplicate definition for GPR register qong: Use generic function for configuring GPR register M28EVK: Enable USB HOST support iMX28: Add USB HOST driver iMX28: Add USB and USB PHY register definitions M28: Add memory detection into SPL iMX28: Fix ARM vector handling M28: Add doc/README.m28 documentation M28: Add MMC SPL iMX28: Add support for DENX M28EVK board iMX28: Add u-boot.sb target to Makefile iMX28: Add image header generator tool iMX28: Add driver for internal RTC iMX28: Add GPMI NAND driver iMX28: Add APBH DMA driver iMX28: Add SPI driver iMX28: Add GPIO control iMX28: Add I2C bus driver iMX28: Add PINMUX control FEC: Add support for iMX28 quirks iMX28: Add SSP MMC driver iMX28: Initial support for iMX28 CPU MX25: zmx25: GCC4.6 fix build warnings da850: add new config file for AM18xx BeagleBoard: config: Switch to ttyO2 OMAP3: Change omap3_evm maintainer devkit8000: Fix NAND SPL on boards with 256MB NAND integrator: enable Vpp and disable flash protection integrator: add system controller header integrator: make flash writeable on boot integrator: use io-accessors for board init integrator: move text offset to config integrator: pass configs for core modules ARM: remove superfluous setting of arch_number in board specific code. SPL: Allow ARM926EJS to avoid compiling in the CPU support code integrator: do not test first part of the memory arm: a320: fix broken timer ARM: define CONFIG_MACH_TYPE for all ronetix boards dm646x: pass board revision info to kernel dm646x: add new configuration for dm6467T arm, davinci: Fix setting of the SDRAM configuration register arm, davinci: Remove the duplication of LPSC functions arm, davinci: Rename AM1808 lowlevel functions to DA850 da8xxevm: fix build error ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE