u-boot.git/drivers/usb/host, branch v2016.11-rc2

usb: pci: Fix cast for 64-bit compilation

2016-10-11T03:55:33Z

Fix a cast that causes warnings on 64-bit machines. Signed-off-by: Simon Glass Reviewed-by: Bin Meng

Merge branch 'master' of git://git.denx.de/u-boot-usb

2016-10-01T01:58:44Z

Signed-off-by: Tom Rini Conflicts: include/configs/dra7xx_evm.h

drivers: usb: xhci-fsl: Implement Erratum A-010151 for FSL USB3 controller

2016-09-27T21:30:49Z

Currently the controller by default enables the Receive Detect feature in P3 mode in USB 3.0 PHY. However, USB 3.0 PHY does not reliably support receive detection in P3 mode. Enabling the USB3 controller to configure USB in P2 mode whenever the Receive Detect feature is required. Signed-off-by: Sriram Dash Signed-off-by: Rajesh Bhagat

usb: host: ehci-vf: Migrate Vybrid USB to driver model

2016-09-27T21:30:22Z

Add driver model support for Vybrid USB driver. Signed-off-by: Sanchayan Maity

drivers: usb: xhci-fsl: Change burst beat and outstanding pipelined transfers requests

2016-09-27T21:30:16Z

This is required for better performance, and performs below tuning: 1. Enable burst length set, and define it as 4/8/16. 2. Set burst request limit to 16 requests. Signed-off-by: Rajesh Bhagat Signed-off-by: Sriram Dash

Merge branch 'master' of git://git.denx.de/u-boot-tegra

2016-09-27T16:47:25Z

ARM: tegra: fix USB ULPI PHY reset signal inversion confusion

2016-09-27T16:11:03Z

USB ULPI PHY reset signals are typically active low. Consequently, they should be marked as GPIO_ACTIVE_LOW in device tree, and indeed they are in the Linux kernel DTs, and in DT properties that U-Boot doesn't yet use. However, in DT properties that U-Boot does use, the value has been set to 0 (== GPIO_ACTIVE_HIGH) to work around a bug in U-Boot. This change fixes the DT to correctly represent the HW, and fixes the Tegra USB driver to cope with the fact that dm_gpio_set_value() internally handles any inversions implied by the DT value GPIO_ACTIVE_LOW. Cc: Marcel Ziswiler Signed-off-by: Stephen Warren Reviewed-by: Simon Glass Signed-off-by: Tom Warren

usb: xhci-mvebu: Add Armada 8K to compatiblity list

2016-09-27T15:29:54Z

To enable this driver on Armada 7K/8K this patch adds the compatibility property to the list. Signed-off-by: Stefan Roese Cc: Nadav Haklai Cc: Neta Zur Hershkovits Cc: Kostya Porotchkin Cc: Omri Itach Cc: Igal Liberman Cc: Haim Boot Cc: Hanna Hawa

usb: ehci: ehci-marvell.c: Add Armada 3700 support (ARMv8)

2016-09-27T15:29:53Z

This patch adds DM based support for the Armada 3700 EHCI controller. The address windows don't need to get configured in this case. The difference here is detected via DT compatible property at runtime. With this support and the DM xHCI driver, both XHCI and eHCI can be used simultaniously on the MVEBU boards now. Signed-off-by: Stefan Roese Cc: Nadav Haklai Cc: Kostya Porotchkin Cc: Wilson Ding Cc: Victor Gu Cc: Hua Jing Cc: Terry Zhou Cc: Hanna Hawa Cc: Haim Boot Acked-by: Marek Vasut

usb: xhci: Add Marvell MVEBU xHCI support

2016-09-27T15:29:52Z

This patch adds DM based support for the xHCI USB 3.0 controller integrated in the Armada 3700 SoC. It may be extended to be used by other MVEBU SoCs as well. Signed-off-by: Stefan Roese Cc: Nadav Haklai Cc: Kostya Porotchkin Cc: Wilson Ding Cc: Victor Gu Cc: Hua Jing Cc: Terry Zhou Cc: Hanna Hawa Cc: Haim Boot Acked-by: Marek Vasut