The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.

However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.

The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>

adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
So  adopt 32 bit address for CONFIG_PPC.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Per feedback from Marek, he suggested better handling and
to enable DM_FLAG_OS_PREPARE, this patch re-orders some of
the error checking, and errors returns the error code right
away and also sets DM_FLAG_OS_PREPARE.

Signed-off-by: Adam Ford <aford173@gmail.com>

This patch reuses some former code for the hawkboard, combines it
with some some similar DM_USB compatible code for the OHCI driver,
and enables the use of the da850's OHCI controller with DM_USB
compatibility.

Signed-off-by: Adam Ford <aford173@gmail.com>

There is a delay function that was commented out.  This patch
re-enables it, because it will be needed for da850 ohci support.

Signed-off-by: Adam Ford <aford173@gmail.com>

This converts the following to Kconfig:
   CONFIG_USB_EHCI_MX5

Signed-off-by: Lukasz Majewski <lukma@denx.de>

This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB).
It is a straightforward conversion (to reuse as much code as possible),
based on ehci-mx6.c code.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

Move CONFIG_USB_EHCI_VF to drivers/usb/host/Kconfig and update the one
and only user thereof being colibri_vf.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>

There exists code in drivers/common/common.c to read the dr_mode
from the device tree.  This patch converts this driver to use that
function to initialize the driver.

Signed-off-by: Adam Ford <aford173@gmail.com>

Drop the counter, it has no meaning other than being the order in which
the interface is found; the name assigned to the USB host controller
interface is a better indicator.

Example of the original output:
> USB0:   USB EHCI 1.10
> scanning bus 0 for devices... 2 USB Device(s) found
>        scanning usb for storage devices... 1 Storage Device(s) found

Patched output:
> Bus usb@ee080100: USB EHCI 1.10
> scanning bus usb@ee080100 for devices... 2 USB Device(s) found
>        scanning usb for storage devices... 1 Storage Device(s) found

Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>