u-boot.git/drivers/usb/host, branch v2024.01-rc2

Kconfig: Remove all default n/no options

2023-10-30T19:32:49Z

Similar change was done by commit b4c2c151b14b ("Kconfig: Remove all default n/no options") and again sync is required. default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek Reviewed-by: Svyatoslav Ryhel # tegra Reviewed-by: Tom Rini Reviewed-by: Angelo Dureghello

usb: ehci: mxs: Use regulator_set_enable_if_allowed()

2023-10-16T06:46:01Z

Since commit 4fcba5d556b4 ("regulator: implement basic reference counter") the return value of regulator_set_enable() may be EALREADY or EBUSY for fixed/GPIO regulators. Switch to using the more relaxed regulator_set_enable_if_allowed() to continue if regulator already was enabled or disabled. This fixes the following error when running the 'ums' command: => ums 0 mmc 0 UMS: LUN 0, dev mmc 0, hwpart 0, sector 0x0, count 0xece000 Error enabling VBUS supply g_dnl_register: failed!, error: -114 g_dnl_register failed Signed-off-by: Fabio Estevam Reviewed-by: Marek Vasut

usb: ehci: mxs: Fix the USB node pointer retrieval

2023-10-16T06:46:01Z

Use dev_ofnode() to retrieve the USB node pointer from the udevice structure. This fixes the following build error: drivers/usb/host/ehci-mxs.c:143:38: error: 'struct udevice' has no member named 'node_' Signed-off-by: Fabio Estevam Reviewed-by: Marek Vasut

common: Drop linux/printk.h from common header

2023-09-24T13:54:57Z

This old patch was marked as deferred. Bring it back to life, to continue towards the removal of common.h Move this out of the common header and include it only where needed. Signed-off-by: Simon Glass

bootstd: Keep track of use of usb stop

2023-09-21T22:05:40Z

When 'usb stop' is run, doing 'bootflow scan' does not run the USB hunter again so does not see any devices. Fix this by telling bootstd about the state of USB. Signed-off-by: Simon Glass

board: usb: Replace legacy usb_gadget_handle_interrupts()

2023-09-15T21:38:02Z

The usb_gadget_handle_interrupts() is no longer used anywhere, replace the remaining uses with dm_usb_gadget_handle_interrupts() which takes udevice as a parameter. Some of the UDC drivers currently ignore the index parameter altogether, those also ignore the udevice and have to be reworked. Other like the dwc3_uboot_handle_interrupt() had to be switched from index to udevice look up to avoid breakage. Reviewed-by: Mattijs Korpershoek Tested-by: Mattijs Korpershoek # on khadas vim3 Signed-off-by: Marek Vasut

usb: sandbox: Add DM_USB_GADGET support

2023-09-15T21:38:01Z

Remove local usb_gadget_register_driver()/usb_gadget_unregister_driver() implementation which is implemented in udc-core.c instead if DM_USB_GADGET is enabled. Add no-op dm_usb_gadget_handle_interrupts() implementation. Reviewed-by: Mattijs Korpershoek Reviewed-by: Simon Glass Signed-off-by: Marek Vasut

usb: host: ohci-generic: Make usage of clock/reset bulk() API

2023-09-04T16:25:20Z

Make usage of clock and reset bulk API in order to simplify the code Reviewed-by: Marek Vasut Signed-off-by: Fabrice Gasnier Reviewed-by: Xavier Drudis Ferran

usb: check for companion controller in uclass

2023-09-04T16:25:20Z

EHCI is usually used with companion controller (like OHCI) as companion controller. This information on the companion is missing currently in companion drivers. So, if the usb-uclass isn't aware, it may scan busses in any order: OHCI first, then EHCI. This is seen on STM32MP1 where DT probing makes the probe order to occur by increasing address (OHCI address < EHCI address). When a low speed or full-speed device is plugged in, it's not detected as EHCI should first detect it, and give ownership (handover) to OHCI. Current situation on STM32MP1 (with a low speed device plugged-in) STM32MP> usb start starting USB... Bus usb@5800c000: USB OHCI 1.0 Bus usb@5800d000: USB EHCI 1.00 scanning bus usb@5800c000 for devices... 1 USB Device(s) found scanning bus usb@5800d000 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found The "companion" property in the device tree allow to retrieve companion controller information, from the EHCI node. This allow marking the companion driver as such. With this patch (same low speed device plugged in): STM32MP> usb start starting USB... Bus usb@5800c000: USB OHCI 1.0 Bus usb@5800d000: USB EHCI 1.00 scanning bus usb@5800d000 for devices... 1 USB Device(s) found scanning bus usb@5800c000 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found STM32MP> usb tree USB device tree: 1 Hub (12 Mb/s, 0mA) | U-Boot Root Hub | +-2 Human Interface (1.5 Mb/s, 100mA) HP HP USB 1000dpi Laser Mouse 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller This also optimize bus scan when a High speed device is plugged in, as the usb-uclass skips OHCI in this case: STM32MP> usb reset resetting USB... Bus usb@5800c000: USB OHCI 1.0 Bus usb@5800d000: USB EHCI 1.00 scanning bus usb@5800d000 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found STM32MP> usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) | u-boot EHCI Host Controller | +-2 Mass Storage (480 Mb/s, 200mA) SanDisk Cruzer Blade 03003432021922011407 Signed-off-by: Fabrice Gasnier Reviewed-by: Marek Vasut

Merge tag 'v2023.10-rc3' into next

2023-08-21T21:32:17Z

Prepare v2023.10-rc3 Signed-off-by: Tom Rini