* 'master' of git://git.denx.de/u-boot-arm:
  tegra: define fdt_load/fdt_high variables
  tegra: enable bootz command
  tegra: usb: Fix device enumeration problem of USB1
  tegra: trimslice: set up serial flash pinmux
  tegra: add pin_mux_spi() board initialization function
  tegra: add GMC/GMD funcmux entry for SFLASH
  tegra: bootcmd: start USB only when needed
  tegra: bootcmd enhancements
  tegra: add enterrcm command
  tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
  Add env vars describing U-Boot target board
  tegra: usb: fix wrong error check
  tegra: add ULPI on USB2 funcmux entry
  tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
  tegra: Add Tamonten Evaluation Carrier support
  tegra: Use SD write-protect GPIO on Tamonten
  tegra: Implement gpio_early_init() on Tamonten
  tegra: Allow boards to perform early GPIO setup
  tegra: plutux: Add device tree support
  tegra: medcom: Add device tree support
  tegra: Rework Tamonten support
  beagle: add eeprom expansion board info for bct brettl4

Signed-off-by: Wolfgang Denk <wd@denx.de>

A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.

Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>

This patch adds a function to set usb host mode to USB 2.0 HOST Link
for EXYNOS5

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>

This patch incorates the review comments given by Minkyu Kang for
EHCI support on EXYNOS

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>

Commit 7a101e946cba55e32d3d1265e30456c810046da3 introduced following warning:
---8<---
ehci-atmel.c: In function 'ehci_hcd_init':
ehci-atmel.c:49:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
ehci-atmel.c: In function 'ehci_hcd_stop':
ehci-atmel.c:79:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
--->8---

This patch fixes it.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Bo Shen <voice.shen@atmel.com>
cc: Marek Vasut <marex@denx.de>

Some Atmel SoC support USB EHCI, add the EHCI driver to support it.

To enable the USB EHCI, add the following configuration options into
board relative configuration file and remove USB OHCI options.

    #define CONFIG_USB_EHCI
    #define CONFIG_USB_EHCI_ATMEL
    #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS     2

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

These are all the files which use the API incorrectly but did not get
built using MAKEALL -a powerpc|arm.  I have no compiler for them, but
the remaining issues should be far less than without this patch.

Any outstanding issues are left to the maintainers of boards that use
these drivers.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

Fix:
asix.c: In function 'asix_eth_get_info':
asix.c:629:12: warning: assignment from incompatible pointer type

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
smsc95xx.c: In function 'smsc95xx_eth_get_info':
smsc95xx.c:869:12: warning: assignment from incompatible pointer type
[enabled by default]

Signed-off-by: Anatolij Gustschin <agust@denx.de>