u-boot.git/drivers/usb, branch v2014.01-rc2

drivers/usb/gadget: select objects by obj-$(CONFIG-...)

2013-12-13T14:18:44+00:00

Before switching to the real Kbuild, drivers/usb/gadget/Makefile
must be fixed.
If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE
is defined, both obj- and obj-y get empty.

We need non-empty obj- or obj-y on each Makefile
to generate built-in.o on the real Kbuild.

Signed-off-by: Masahiro Yamada

Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'

2013-12-06T15:54:42+00:00

usb: ehci-omap: Reset the USB Host OMAP module

2013-12-06T12:02:32+00:00

In commit bb1f327 we removed the UHH reset to fix NFS root (over usb
ethernet) problems with Beagleboard (3530 ES1.0). However, this
seems to cause USB detection problems for Pandaboard, about (3/8).

On further investigation, it seems that doing the UHH reset is not
the cause of the original Beagleboard problem, but in the way the reset
was done.

This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based
on the UHH_REVISION register. This should fix the Beagleboard NFS
problem as well as the Pandaboard USB detection problem.

Reported-by: Tomi Valkeinen 
CC: Stefan Roese 
Reviewed-by: Stefan Roese 
Signed-off-by: Roger Quadros

driver:usb:s3c_udc: add support for Exynos4x12

2013-12-02T02:22:32+00:00

This patch add new defines for usb phy for Exynos4x12.

Signed-off-by: Piotr Wilczek 
Signed-off-by: Kyungmin Park 
Signed-off-by: Minkyu Kang

usb, g_dnl: make bcdDevice value configurable

2013-11-12T14:53:59+00:00

add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.

Signed-off-by: Heiko Schocher 
Acked-by: Lukasz Majewski 
Cc: Marek Vasut 
Cc: Kyungmin Park

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

2013-11-09T21:59:47+00:00

Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h

usb, g_dnl: make iSerialNumber board configurable

2013-11-08T19:46:20+00:00

add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().

Signed-off-by: Heiko Schocher 
Cc: Marek Vasut 
Cc: Lukasz Majewski 
Cc: Kyungmin Park 
Tested-by: Lukasz Majewski

usb: ohci-hcd: submit_common_msg: report actual_length properly

2013-11-08T19:46:19+00:00

submit_common_msg should report amount of data passed from/to device.
Instead, it always returned size requested by Host.

Signed-off-by: Mateusz Kulikowski

usb: ums: add ums exit feature by ctrl+c or by detach usb cable

2013-11-08T19:46:19+00:00

This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.

Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.

Changes v2:
- add a note to the README

Signed-off-by: Przemyslaw Marczak 
Cc: Marek Vasut

usb: ums: fix disk capacity miscalculation and code cleanup

2013-11-08T19:46:19+00:00

This patch prevents:
- ums disk capacity miscalculation because of integer overflow

Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
  initialization before gadget init
- Remove unnecessary code from mass storage driver

Signed-off-by: Przemyslaw Marczak 
Cc: Marek Vasut