Including <common.h> pulls in a lot of bloat.  What this driver needs
is BIT(), so replace it with <linux/bitops.h>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>

Collect runtime BUG/WARN into a self-contained header <linux/bug.h>
to make these macros easier to use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>

When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*().  U-Boot does not support them in a clean
way.  So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.

We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround.  Hence this
patch, to find the best home for all printk variants.  If you want to
use printk() and friends, please include <linux/printk.h>.  This header
is self-contained, and pulls in only a few headers.

When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards.  This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.

To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel".  (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.

The difference is the loglevel is build-time determined.  To save the
image size, lower priority pr_*() are compiled out.  I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.

I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>

Since we use EHCI generic driver on RCar Gen3 , this driver is useless.
Remove it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

USB_GADGET will fail to compile if USB_MUSB_GADGET is not defined. Make
sure we have that condition right.

Fixes: e0ea88042d51 ("sunxi: Imply USB_ETHER")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The device model was implemented so far using a hook that needed to be
called from the board support, without DT support and only for the host.

Switch to probing both in peripheral and host mode through the DT.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

All the Allwinner boards use the same manufacturer, VID and PID for the
gadgets. Make them the defaults to remove some boilerplate from our
defconfigs.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>