u-boot.git/drivers/usb, branch v2020.07

eth/r8152: update the firmware

2020-06-14T11:36:29Z

Update the firmware to improve compatibility for none-intel USB host controller. The more information is as following. The device has auto-installed driver feature - via switch CD-ROM/NIC mode. But in some corner cases, it would switch to CD-ROM unexpected. This issue results in Lan Function Disabled. While USB PHY transits to P3 from P0 due to the absent of transmitter control, it would issues undefined signal to its link partner. Some Down Stream Port misidentify the undefined signal as wakeup signal. So the link state will not keep in suspend even the system is idle. Signed-off-by: Hayes Wang

kconfig: fix typo for OHCI host and add to DM list

2020-06-02T21:27:04Z

Description said that OHCI is not supported for driver model while it was converted too. Signed-off-by: Marcin Juszkiewicz

usb: ohci: Add header file for ARCH_DMA_MINALIGN

2020-06-02T17:06:10Z

This is defined in the asm/cache.h header file. Update this header file to include it so it gets the same value consistently across U-Boot. This fixes 'usb host' on omapl138_lcdk. Fixes: 90526e9fbac ("common: Drop net.h from common header") Reported-by: Adam Ford Signed-off-by: Simon Glass Tested-by: Adam Ford Reviewed-by: Tom Rini

Merge tag 'u-boot-rockchip-20200531' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip

2020-06-01T00:07:39Z

- Fix mmc of path after syncfrom kernel dts; - Add dwc3 host support with DM for rk3399; - Add usb2phy and typec phy for rockchip platform; - Migrate board list doc to rockchip.rst; - Add rk3399 Pinebook Pro board support; - Update dram_init in board_init and add memory node in SPL;

driver: usb: drop legacy rockchip xhci driver

2020-05-29T23:38:50Z

We have changed to use dwc3 generic driver for usb3.0 host, so the legacy Rockchip's xHCI driver is not needed, and drop it. Signed-off-by: Frank Wang Reviewed-by: Jagan Teki Reviewed-by: Kever Yang

usb: dwc3: add make compatible for rockchip platform

2020-05-29T23:38:50Z

RK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller in resetting to hold pipe power state in P2 before initializing the PHY. This commit fixed it and added device compatible for rockchip platform. Signed-off-by: Frank Wang Signed-off-by: Jagan Teki Reviewed-by: Kever Yang

usb: ehci-mx6: Print error code on failure

2020-05-29T17:23:36Z

Print the error code if the regulator enable fails, otherwise the error message is rather useless and confusing. Signed-off-by: Marek Vasut

usb: ehci-mx6: Handle fixed regulators correctly

2020-05-29T17:18:55Z

The regulator-fixed would return -ENOSYS when enabled/disabled, because this operation is not supported, but this is not an error e.g. on systems where the VBUS cannot be controlled, so if this is the error code reported by the regulator core, consider it a success and continue. Signed-off-by: Marek Vasut

eth/r8152: fix assigning the wrong endpoint

2020-05-29T17:18:55Z

Although I think it never occurs, the code doesn't make sense, because it may allow to assign an IN endpoint to ss->ep_out. Signed-off-by: Hayes Wang

usb: dwc3: amend UTMI/UTMIW phy interface setup

2020-05-29T10:13:19Z

Let move 8/16-bit UTMI+ interface initialization into DWC3 core init that is convenient for both DM_USB and u-boot traditional process. Signed-off-by: Frank Wang Signed-off-by: Jagan Teki Reviewed-by: Kever Yang