u-boot.git/drivers/usb, branch v2021.04-rc2

Merge branch '2021-02-02-drop-asm_global_data-when-unused'

2021-02-15T15:16:45Z

- Merge the patch to take out of

usb: dwc2: change compatible st,stm32mp1-hsotg to st,stm32mp15-hsotg

2021-02-10T21:23:35Z

The Linux kernel v5.7-rc1 introduced the compatible "st,stm32mp15-hsotg". See Linux kernel commit d49850110434 ("dt-bindings: usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS") This patch updates the supported compatible in DWC2 driver, removes the add-on done in U-Boot dtsi and keeps the compatible defined in SOC dtsi arch/arm/dts/stm32mp151.dtsi: usbotg_hs: usb-otg@49000000 { compatible = "st,stm32mp15-hsotg", "snps,dwc2"; reg = <0x49000000 0x10000>; ... }; Signed-off-by: Patrick Delaunay

usb: xhci: Fix compare to use physical addresses in xhci_bulk_tx()

2021-02-10T21:23:24Z

Testing with v2021.01 on MIPS Octeon has shown, that the latest patch for the "short packet event trb handling" did introduce a bug on platforms with virtual address != physical address. This patch fixes this issue by using the correct address types in the compare (both physical in this case). Signed-off-by: Stefan Roese Cc: Aaron Williams Cc: Chandrakala Chavva Cc: Ran Wang Cc: Nicolas Saenz Julienne Cc: Marek Vasut Cc: Bin Meng

usb: xhci-pci: Check for errors from dm_pci_map_bar()

2021-02-10T21:23:24Z

Function dm_pci_map_bar() may fail and returns NULL. Check this to prevent dereferencing a NULL pointer. In xhci-pci this may happen when board does not enable CONFIG_PCI_PNP and PCI_BASE_ADDRESS_0 contains unconfigured zero address. Signed-off-by: Pali Rohár

usb: xhci-mtk: support option to disable ports

2021-02-10T21:23:24Z

Add support to disable specific ports, it's useful for some scenarios: 1. usb3 PHY is shared whith PCIe or SATA, the corresponding usb3 port can be disabled; 2. some usb2 or usb3 ports are not used on special platforms, they should be disabled to save power. Signed-off-by: Chunfeng Yun

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42Z

Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include at all, so remove that include. Signed-off-by: Simon Glass Signed-off-by: Tom Rini

usb: gaget: ci: set ep's desc when enable ep

2021-01-31T13:08:56Z

As we need standard usb_ep's desc, so set it when enable ep. Reviewed-by: Peter Chen Signed-off-by: Li Jun Signed-off-by: Peng Fan

usb: gadget: fastboot: use correct max packet size

2021-01-31T13:08:56Z

Change to use wMaxPacketSize of current speed EP desc for request length wrap up. Reviewed-by: Peter Chen Signed-off-by: Li Jun Signed-off-by: Peng Fan

usb: udc: ci: update speed handling

2021-01-31T13:08:56Z

Remove the gadget driver speed check, and set its max_speed to be USB_SPEED_HIGH. Reviewed-by: Ye Li Reviewed-by: Peter Chen Tested-by: faqiang.zhu Signed-off-by: Li Jun Signed-off-by: Peng Fan

usb: composite: force gadget to be USB2 for HS only function

2021-01-31T13:08:56Z

If one of functions is not super speed capable, we need force the udc to be high speed, this is an equivalent implementation of usb_gadget_udc_set_speed() in kernel but simple, which set the gadget max_speed to be high speed, so afterwards when start gadget duc can set the HW to be USB 2.0 mode. Reviewed-by: Ye Li Reviewed-by: Peter Chen Tested-by: faqiang.zhu Signed-off-by: Li Jun Signed-off-by: Peng Fan