dev_read_size() returns -EINVAL (-22) if the property "g-tx-fifo-size"
does not exist. If that's the case, we now keep the default value of 0.

Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>

With the omap-ehci driver now using the phy subsystem to enable
and disable reset, the driver no longer needs to know which
GPIO's are used, and they can be removed from Kconfig.

Signed-off-by: Adam Ford <aford173@gmail.com>

There are a few boards that use hard-coded GPIO definitions in
their respective defconfig files.  If the GPIO's are listed
in their device trees, the nop-phy can toggle the GPIO's,
so the EHCI driver does not need to know anything about the
GPIO's. Add functions for getting the phys and remove the GPIO
toggles since the phy will now do that.

Signed-off-by: Adam Ford <aford173@gmail.com>

The USB_EHCI_OMAP driver currently has a series of Kconfig options
which let users specify a GPIO for the reset pin.  Some devices
may have only one reset, while others might have more.

Since there is a nop phy driver, let's selct enable the PHY
system, and imply the nop phy driver.  The nop phy driver can now
toggle the reset pins when putting the phy in and out of reset.

If the gpio is listed under the phy, it will get toggled and
the hard-coded config options specifying the GPIO numbers can
eventually go away.

Signed-off-by: Adam Ford <aford173@gmail.com>

The OMAP3 hierarchy has the ehci node as a sub-node of the
usbhshost. The usbhshost node contains an ohci and an ehci
subnode.  The configuration of the ehci belongs in the
EHCI node and not its parent.  Move it to the proper probe.

usb start
  starting USB...
  Bus ehci@48064800: USB EHCI 1.00
  Bus usb_otg_hs@480ab000: Port not available.
  scanning bus ehci@48064800 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Signed-off-by: Adam Ford <aford173@gmail.com>

omap_ehci_hcd_stop appears to be dead code, and omap_ehci_hcd_init
is only called by the probe function, so it can be static to that
function.  Remove both from the header along with some additional
checking for DM_USB.

Signed-off-by: Adam Ford <aford173@gmail.com>

- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)

Official DT bindings use compatible string marvell,armada-3700-ehci.
Update drivers and DTS files.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

There are devices which cause a USB stall when trying to read strings.
Specifically Arduino Mega R3 stalls when trying to read the product
string.

The stall currently remains unhandled, and subsequent retries submit new
transfers on a stopped endpoint which ultimately cause a crash in
abort_td():
WARN halted endpoint, queueing URB anyway.
XHCI control transfer timed out, aborting...
Unexpected XHCI event TRB, skipping... (3affe040 00000000 13000000 02008401)
BUG at drivers/usb/host/xhci-ring.c:505/abort_td()!
BUG!
resetting ...

Linux seems to be able to recover from the stall by issuing a
TRB_RESET_EP command.

Introduce reset_ep() which issues a TRB_RESET_EP followed by setting the
transfer ring dequeue pointer via TRB_SET_DEQ. This allows to properly
recover from a USB stall error and continue communicating with the USB
device.

Signed-off-by: Stefan Agner <stefan@agner.ch>

If u-boot doesn't stop the core when it's finished with it then
linux can't find it.

Signed-off-by: Angus Ainslie <angus@akkea.ca>