u-boot.git/drivers/usb, branch v2023.07.01

Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-usb into next

2023-07-06T17:23:36Z

Merge tag 'v2023.07-rc6' into next

2023-07-05T15:28:55Z

Prepare v2023.07-rc6

usb: dwc3-generic: Ensure reset GPIO is configured as an output

2023-07-03T08:46:34Z

GPIOD_ACTIVE_LOW is not enough to configure a GPIO as an output, we need GPIOD_IS_OUT as well. Fixes: b252d79b0936d60b ("usb: dwc3: Add support to reset usb ULPI phy") Signed-off-by: Peter Korsgaard

usb: dwc2: Fix the write to W1C fields in HPRT register

2023-06-21T11:15:58Z

Fix the write to the HPRT register which treat W1C fields as if they were mere RW. This leads to unintended clearing of such fields This bug was found during the testing on Simics model. Referring to specification DesignWare Cores USB 2.0 Hi-Speed On-The-Go (OTG) Databook (3.30a)"5.3.4.8 Host Port Control and Status Register (HPRT)", the HPRT.PrtPwr is cleared by this mistake. In the Linux driver (contrary to U-Boot), HPRT is always read using dwc2_read_hprt0 helper function which clears W1C bits. So after write back those bits are zeroes. Signed-off-by: Teik Heng Chong

usb: eth: lan78xx: Fix logic in lan78xx_read_otp() to avoid a warning

2023-06-20T17:02:59Z

In lan78xx_read_otp() we want to know if sig is LAN78XX_OTP_INDICATOR_1 or LAN78XX_OTP_INDICATOR_2. In the case of matching the first one we set offset to itself, and clang warns about this. Rework the logic so that if sig is the second indicator we adjust the offset as today and if it does not match the first indicator we return -EINVAL Cc: Marek Vasut Reviewed-by: Marek Vasut Signed-off-by: Tom Rini

Merge tag v2023.07-rc4 into next

2023-06-12T18:55:33Z

Signed-off-by: Tom Rini

usb: musb-new: sunxi: remove unused define

2023-06-08T19:57:01Z

This is a remnant from when the USB controller driver managed the reset signal itself. A patch from the very end of 2018 changed this driver to delegate reset (and clock) management to the proper control unit driver, but left this unused define behind. Signed-off-by: Sam Edwards Reviewed-by: Marek Vasut

usb: musb-new: sunxi: fix error check

2023-06-07T21:38:51Z

The `musb_register` function returns some ERR_PTR(...) on failure, not NULL, so update the check here appropriately. Signed-off-by: Sam Edwards Reviewed-by: Marek Vasut

usb: gadget: Add and use matching SPL USB ethernet gadget Kconfig symbols

2023-05-16T23:51:39Z

Define SPL_USB_ETH_RNDIS symbol to make it possible to select USB gadget ethernet support in SPL and U-Boot separately in Kconfig . Make use of the new symbols in gadget Makefile and move the rndis.o just below the now merged USB_ETHER symbol in Makefile. Signed-off-by: Marek Vasut Reviewed-by: Tom Rini

usb: Move SPL_USB_GADGET and related Kconfig symbols to drivers/usb/

2023-05-16T23:51:39Z

To avoid piling up all the various Kconfig symbols in one place, i.e. common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ . This commit moves SPL_USB_GADGET and related symbols. Fix typo and rename SPL_USB_GADGET to "USB Gadget Support in SPL" . Update the gadget Makefile to match the symbol changes. Signed-off-by: Marek Vasut Reviewed-by: Tom Rini