The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe.  Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The function find_sector() does not take into account if the flash bank
has changed since the last call. This could lead to illegal accesses inside
and beyond the flash_info_t info strcture. For example if the current
flash bank has less sectors than the last used flash bank.

This patch adds two cheks. One that insures, that the current sector does
not exceed the allowed maximum (which is always a good idea). And one that
checks if the current access is to the same flash bank as the last access.
If not, the search loop will start with sector 0.

Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Blocksize was hardcoded to 512 bytes. But the blocksize varies
depeding on various mmc subsystem commands (between 8 and 512).
This hardcoding was resulting in interrupt error during data
transfer.

It is now calculated based upon the request sent by mmc subsystem.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Use get_timer() the same way as drivers/net/ftgmac100.c

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Reviewed-by: Macpaul Lin <macpaul@gmail.com>
Tested-by: Macpaul Lin <macpaul@gmail.com>

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Reviewed-by: Macpaul Lin <macpaul@gmail.com>
Tested-by: Macpaul Lin <macpaul@gmail.com>

SH7757 has ETHER and GETHER. This patch supports EHTER only.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

- Timeout counter value is set as DTOCV bits in SYSCTL register
  For counter value set as timeout,
  Timeout period = (2^(timeout + 13)) SD Clock cycles

- As per 4.6.2.2 section of SD Card specification v2.00, host should
  cofigure timeout period value to minimum 0.25 sec.

- Number of SD Clock cycles for 0.25sec should be minimum
	(SD Clock/sec * 0.25 sec) SD Clock cycles
	= (mmc->tran_speed * 1/4) SD Clock cycles

- Calculating timeout based on
	(2^(timeout + 13)) >=  mmc->tran_speed * 1/4
	Taking log2 both the sides and rounding up to next power of 2
	=> timeout + 13 = log2(mmc->tran_speed/4) + 1

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We had an extra '0x' in the output of the LAWAR header that would cause
output like:

LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d

intead of:

LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>