Signed-off-by: Wolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-arm:
  ARM926EJS: Fix cache.c to comply with checkpatch.pl
  ARM926EJS: Make asm routines volatile in cache ops
  MX35: mx35pdk: wrong board revision
  ARM1136: MX35: Make asm routines volatile in cache ops
  ARM: add u-boot.imx as target for i.MX SOCs
  M28: Pull out CONFIG_APBH_DMA so it's always enabled
  DMA: Split the APBH DMA init into block and channel init
  imx: Return gpio_set_value in gpio_direction_output
  imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5)
  imx: Add GPIO_TO_PORT macro in the mxc_gpio driver
  imx: Remove unneeded/repititive definitions from imx headers
  i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
  MX31: mx31pdk: drop enable_caches from board file
  i.MX28: Fix initial stack pointer position
  mx35: mx35pdk: fix when cache functions are linked
  mx35: flea3: fix when cache functions are linked
  ARM: 926ejs: use debug() for misaligned addresses
  ARM1136: add cache flush and invalidate operations
  mx6qsabrelite: Fix the serial console port
  mx6qsabrelite: Add boot switch setting information into the README
  i.MX6: mx6qsabrelite: add cache commands if cache is enabled
  i.MX6: implement enable_caches()
  i.MX6: define CACHELINE_SIZE
  MX53: DDR: Fix ZQHWCTRL field TZQ_CS
  mx28evk: Add a README file
  mx28: Split the README into a common part and a m28 specific part
  tricorder: Load kernel from ubifs
  tricorder: Add UBIFS
  cm-t35: fix Ethernet reset timing
  hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
  BeagleBoard: Remove userbutton command and use gpio command instead
  OMAP: Move omap1510inn to Unmaintained / Orphaned

This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.

The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.

The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.

NOTE: This patch depends on:

	http://patchwork.ozlabs.org/patch/150957/

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

Return gpio_set_value in gpio_direction_output.
Earlier it returned 0 and ignored gpio_set_value's return value.

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>

Use the defined GPIO_TO_PORT macro. Remove gpio >> 5 references.

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>

Add GPIO_TO_PORT macro in the mxc_gpio.c driver

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>

This SD DMA function of i.MX28 is still apparently too experimental to be
enabled by default in 2012.04 release. Enable this feature only if the user
plans to tinker with DCache or explicitly enables it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>

Fix:
spr_smi.c: In function 'smi_write':
spr_smi.c:325:15: warning: variable 'WM' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>

* 'master' of git://git.denx.de/u-boot-net:
  net/designware: Change timeout loop implementation
  net/designware: Set ANAR to 0x1e1
  net/designware: Program phy registers when auto-negotiation is ON
  net/designware: Try configuring phy on each dw_eth_init
  net/designware: Consecutive writes must have delay
  net/designware: Phy address fix
  net/designware: Fix the max frame length size
  net/designware: Fix to restore hw mac address
  microblaze: Wire up LL_TEMAC driver initialization
  microblaze: Add faked LL_TEMAC driver configuration
  microblaze: Enable several ethernet driver compilation
  net: ll_temac: Add LL TEMAC driver to u-boot
  Update net subsystem maintainer in doc/git-mailrc
  net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
  mvgbe: remove warning for unused methods

The new implementation changes the timeout loop implementation to avoid 1 ms
delay in each failing test. It also configures the delay to 10usec.

Signed-off-by: Amit Virdi <amit.virdi@st.com>