'r' of rESR_RTLF is a mistake of E.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This fixes checkpatch's warning.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The R7S72100 of ARM SoC that Renesas manufactured has one Ether port.
This has the same IP SH-Ether. This patch adds support of the R7S72100
in SH-Ether.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add a driver for the TPS65218 PMIC which is used by TI AM43xx SoCs and
may be used by TI AM335x SoCs.

Signed-off-by: Tom Rini <trini@ti.com>

The patch populates the slave data which will be used by flash driver to
set the  flash quad enable bit.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>

This patch add support for BCH16_ECC to omap_gpmc driver.

*need to BCH16 ECC scheme*
With newer SLC Flash technologies and MLC NAND, and large densities, pagesizes
Flash devices have become more suspectible to bit-flips. Thus stronger
ECC schemes are required for protecting the data.
But stronger ECC schemes have come with larger-sized ECC syndromes which require
more space in OOB/Spare. This puts constrains like;
(a) BCH16_ECC can correct 16 bit-flips per 512Bytes of data.
(b) BCH16_ECC generates 26-bytes of ECC syndrome / 512B.
Due to (b) this scheme can only be used with NAND devices which have enough
OOB to satisfy following equation:
OOBsize per page >= 26 * (page-size / 512)

Signed-off-by: Pekon Gupta <pekon@ti.com>

GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL:    SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
        which is called before probing for devices, hence any ONFI parameter
        information is not available during GPMC initialization.

Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.

This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.

Signed-off-by: Pekon Gupta <pekon@ti.com>

As per following Sections in ONFI Spec, NAND_CMD_READID should use only
lower 8-bit for transfering command, address and data even on x16 NAND device.

*Section: Target Initialization"
"The Read ID and Read Parameter Page commands only use the lower 8-bits of the
 data bus. The host shall not issue commands that use a word data width on x16
 devices until the host determines the device supports a 16-bit data bus width
 in the parameter page."

*Section: Bus Width Requirements*
"When the host supports a 16-bit bus width, only data is transferred at the
 16-bit width. All address and command line transfers shall use only the lower
 8-bits of the data bus. During command transfers, the host may place any value
 on the upper 8-bits of the data bus. During address transfers, the host shall
 set the upper 8-bits of the data bus to 00h."

Thus porting  following commit from linux-kernel to ensure that column address
is not altered to align to x16 bus when issuing NAND_CMD_READID command.

    commit 3dad2344e92c6e1aeae42df1c4824f307c51bcc7
    mtd: nand: force NAND_CMD_READID onto 8-bit bus
    Author: Brian Norris <computersforpeace@gmail.com> (preserving authorship)

    The NAND command helpers tend to automatically shift the column address
    for x16 bus devices, since most commands expect a word address, not a
    byte address. The Read ID command, however, expects an 8-bit address
    (i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
    0x20).

    This fixes the column address for a few drivers which imitate the
    nand_base defaults.

Signed-off-by: Pekon Gupta <pekon@ti.com>

Porting below commit from linux-tree, preserving original authorship & commit log
commit bd9c6e99b58255b9de1982711ac9487c9a2f18be
Author:     Brian Norris <computersforpeace@gmail.com>
mtd: nand: don't use read_buf for 8-bit ONFI transfers

  Use a repeated read_byte() instead of read_buf(), since for x16 buswidth
  devices, we need to avoid the upper I/O[16:9] bits. See the following
  commit for reference:

  commit 05f7835975dad6b3b517f9e23415985e648fb875 (from linux-tree)
  Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
  Date:   Thu Dec 5 22:22:04 2013 +0100

      mtd: nand: don't use {read,write}_buf for 8-bit transfers

  Now, I think that all barriers to probing ONFI on x16 devices are
  removed, so remove the check from nand_flash_detect_onfi().

Signed-off-by: Pekon Gupta <pekon@ti.com>