Even after memory free of phydev, priv is still pointing to the
obsolete address.
So update priv->phydev as NULL after memory free.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Add support for Microchip LAN7500, LAN7800 and LAN7850,
USB to 10/100/1000 Ethernet Controllers.

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

A few years ago STM32F1 SoCs support has been added :
0144caf22ce6acd5c  gpio: stm32: add stm32f1 support
2d18ef2364fd3561a  ARMv7M: add STM32F1 support

But neither STM32F1 dedicated defconfig nor board was
associated to these commits.

Got confirmation from Tom Rini and Matt Porter to remove
all this code [1]

[1] http://u-boot.10912.n7.nabble.com/Remove-STM32F1-support-td301603.html

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert name to show explicitly that we are using milliseconds. For a
watchdog timer this is precise enough.

No functional change intended.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Maximum Data Transfer Size (MDTS) field indicates the maximum
data transfer size between the host and the controller. The
host should not submit a command that exceeds this transfer
size. The value is in units of the minimum memory page size
and is reported as a power of two (2^n).

The spec also says: a value of 0h indicates no restrictions
on transfer size. On the real NVMe card this is normally not
0 due to hardware restrictions, but with QEMU emulated NVMe
device it reports as 0. In nvme_blk_read/write() below we
have the following algorithm for maximum number of logic
blocks per transfer:

u16 lbas = 1 << (dev->max_transfer_shift - ns->lba_shift);

dev->max_transfer_shift being 0 will for sure cause lbas to
overflow. Let's use 20. With this fix, the NVMe driver works
on QEMU emulated NVMe device.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

NVMe should use the nsze value from the queried device. This will
reflect the total number of blocks of the device and fix detecting
my Samsung 960 EVO 256GB.

Original:
Capacity: 40386.6 MB = 39.4 GB (82711872 x 512)

Fixed:
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Signed-off-by: Jon Nettleton <jon@solid-run.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

This adds support to detect the catchall PCI class for NVMe devices.
It allows the drivers to work with most NVMe devices that don't need
specific detection due to quirks etc.

Tested against a Samsung 960 EVO drive.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

This adds nvme_print_info() to show detailed NVMe controller and
namespace information.

Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>