After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.

So let's flush the RX queue whenever we initialize baud rates.

This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt on Raspberry Pis that use pl011 for serial.

Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>

After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.

So let's flush the RX queue whenever we initialize baud rates.

This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt.

Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>

The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.

Also, Dirk's address was wrong in one place; fix that as well.

Signed-off-by: Mario Six <six@gdsys.cc>

Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add a comment indicating that the German key map assumes code page 437.

Add support for character ² (square sign) in the German key map.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Signed-off-by: Marek Behun <marek.behun@nic.cz>

The PCA953x driver uses "gpio@%x_" as the GPIO bank name, where "%x" is
instantiated with the I2C address of the chip. While this works, it
becomes very confusing if a board has multiple PCAs with the same
address on different I2C busses, and it also becomes an issue when a
GPIO's value is to be set via the 'gpio' command, because this command
only ever sets the value of the first device it encounters, leaving the
other devices inaccessible to the command.

As to not break boards that rely on this naming scheme, we introduce a
new device tree string property "label" for the driver. If it exists, it
is used to build a bank name of the form "%s@%x_" (where %x is still
instantiated with the I2C address). If it does not exist, the legacy
labeling scheme is used.

Signed-off-by: Mario Six <mario.six@gdsys.cc>

Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.

This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Ensure that the Atmel TPM driver performs sufficient
validation of the length returned in the TPM response header.
This patch prevents memory corruption if the header contains a
length value that is larger than the destination buffer.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>