u-boot.git/drivers, branch v2019.01-rc1

Revert "serial: ns16550: fix debug uart putc called before init"

2018-12-04T02:50:47+00:00

This reverts commit 6f57c34473d37b8da5e6a3764d0d377d748aeef1 since it
does not seem to work at least on rk3399.

The Rockchip Technical Reference Manual (TRM) for the rk3399 says the baud
rate prescaler register is readable only when USR[0] is zero. Since this
bit is defined as "reserved" in the socfpga cylcone5 TRM, let's rather
drop this than making the ns16550 debug uart more platform specific.

Reported-by: Roosen Henri 
Signed-off-by: Simon Goldschmidt 
Reviewed-by: Philipp Tomsich 
Reviewed-by: Kever Yang

Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblaze

2018-12-04T00:30:54+00:00

Xilinx changes for v2019.01

microblaze:
- Use default functions for memory decoding
- Showing model from DT

zynq:
- Fix spi flash DTs
- Fix zynq_help_text with CONFIG_SYS_LONGHELP
- Tune cse/mini configurations
- Enabling cse/mini testing with current targets

zynqmp:
- Enable gzip SPL support
- Fix chip detection logic
- Tune mini configurations
- DT fixes(spi-flash, models, clocks, etc)
- Add support for OF_SEPARATE configurations
- Enabling mini testing with current targets
- Add mini mtest configuration
- Some minor config setting

nand:
- arasan: Add subpage configuration

net:
- gem: Add 64bit DMA support

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

2018-12-03T22:52:40+00:00

Patch queue for efi - 2018-12-03

This release is fully packed with lots of glorious improvements in UEFI
land again!

  - Make PE images more standards compliant
  - Improve sandbox support
  - Improve correctness
  - Fix RISC-V execution on virt model
  - Honor board defined top of ram (fixes a few boards)
  - Imply DM USB access when distro boot is available
  - Code cleanups

Merge branch 'master' of git://git.denx.de/u-boot-sh

2018-12-03T22:51:45+00:00

- MMC fixes for R-Car Gen3

spi, mpc8xx: migrate to DM_SPI

2018-12-03T15:44:10+00:00

Signed-off-by: Christophe Leroy

drivers: serial: get rid of non DM mpc8xx driver

2018-12-03T15:44:10+00:00

Signed-off-by: Christophe Leroy

drivers: serial: migrate mpc8xx to DM

2018-12-03T15:44:10+00:00

Signed-off-by: Christophe Leroy

drivers: watchdog: add a DM driver for the MPC8xx watchdog

2018-12-03T15:44:10+00:00

This patch adds a DM driver for the MPC8xx watchdog.
Basically, the watchdog is enabled by default from the start and
SYPCR register has to be writen once to set the timeout and/or
deactivate the watchdog. Once written, it cannot be written again.

It means that wdt_stop() can be called before wdt_start() to stop the
watchdog, but cannot be called if wdt_start() has been called.

Signed-off-by: Christophe Leroy

rtc: m41t62: Convert the RTC driver to support the driver model (DM)

2018-12-03T15:44:10+00:00

After this change the m41t62.c can be used with RTC subsystem (i.e. date
command) which uses device model (DM).

Signed-off-by: Lukasz Majewski 
Reviewed-by: Stefan Roese

rtc: m41t62: Extract common RTC handling code to facilitate DM conversion

2018-12-03T15:44:10+00:00

This change facilitates the conversion of m41t62 RTC driver to device
model (DM).

Signed-off-by: Lukasz Majewski 
Reviewed-by: Stefan Roese