u-boot.git/drivers, branch v2019.04-rc2 Unnamed repository; edit this file 'description' to name the repository. Merge tag 'video-for-2019.04-rc2' of git://git.denx.de/u-boot-video 2019-02-16T23:10:53+00:00 Tom Rini trini@konsulko.com 2019-02-16T23:10:53+00:00 500ad54e35c636b0a05170753da58fcd8c8de6f2 - sunxi display DDC probe fallback - support 24bpp BMP files on 16bpp displays 
- sunxi display DDC probe fallback
- support 24bpp BMP files on 16bpp displays
Merge branch 'master' of git://git.denx.de/u-boot-sh 2019-02-16T22:05:51+00:00 Tom Rini trini@konsulko.com 2019-02-16T22:05:51+00:00 7a2ab3778c0acae27edc01009c6ad9950a90634e - Various MMC fixes 
- Various MMC fixes
mmc: tmio: sdhi: Configure DT2FF register for HS400 mode 2019-02-16T17:12:17+00:00 Marek Vasut marek.vasut+renesas@gmail.com 2019-02-14T14:16:15+00:00 261445dfafdce252f91fea16517aba5830dd1930 The DT2FF register must be configured differently for HS400 mode and for HS200/SDR104 mode. Configure the DT2FF register according to the recommended datasheet settings for each mode. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> 
The DT2FF register must be configured differently for HS400 mode
and for HS200/SDR104 mode. Configure the DT2FF register according
to the recommended datasheet settings for each mode.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
mmc: tmio: Configure HOST_MODE WMODE according to bus width 2019-02-16T17:12:17+00:00 Marek Vasut marek.vasut+renesas@gmail.com 2019-02-14T14:16:24+00:00 4c80f111c06f9aa258b9e55db1ee99572428c105 Set the HOST_MODE register WMODE bit according to the SDHI bus width, that is 0 for 64bit bus and 1 for 16/32bit bus. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> 
Set the HOST_MODE register WMODE bit according to the SDHI bus width,
that is 0 for 64bit bus and 1 for 16/32bit bus.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
mmc: Downgrade SD/MMC from UHS/HS200/HS400 modes before boot 2019-02-16T17:12:17+00:00 Marek Vasut marek.vasut+renesas@gmail.com 2019-01-29T03:45:51+00:00 fceea9926804c8e72bdcde27bf64bebedcf0a754 Older kernel versions or systems which do not connect eMMC reset line properly may not be able to handle situations where either the eMMC is left in HS200/HS400 mode or SD card in UHS modes by the bootloader and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card to non-UHS mode before booting the kernel to allow such older kernels to work with modern U-Boot. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> 
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Merge tag 'u-boot-imx-2019-02-16' of git://git.denx.de/u-boot-imx 2019-02-16T13:31:05+00:00 Tom Rini trini@konsulko.com 2019-02-16T13:31:05+00:00 b89074f65047c4058741ed2bf3e6ff0c5af4c5bc u-boot-imx-2019-02-16 --------------------- - vhybrid: add calibration - gw_ventana: fixes - Improve documentation for Secure Boot (HABv4) - Fix Marvell Switch - MX6 Sabre, switch to DM - Fixes for NAND 
u-boot-imx-2019-02-16
---------------------

- vhybrid: add calibration
- gw_ventana: fixes
- Improve documentation for Secure Boot (HABv4)
- Fix Marvell Switch
- MX6 Sabre, switch to DM
- Fixes for NAND
imx: serial_mxc: disable ri and dcd irq in dte mode 2019-02-15T21:01:15+00:00 Max Krummenacher max.krummenacher@toradex.com 2019-02-01T15:04:50+00:00 a24532083c78fd599807e0af58410a5b406330b5 If the UART is used in DTE mode the RI and DCD bits in UCR3 become irq enable bits. Both are set to enabled after reset and both likely are pending. Disable the bits to prevent an interrupt storm when Linux enables the UART interrupts. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> 
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.

Disable the bits to prevent an interrupt storm when Linux enables
the UART interrupts.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
mmc: fsl_esdhc: Fix DM_REGULATOR ifdefs for SPL builds 2019-02-15T21:01:15+00:00 Abel Vesa abel.vesa@nxp.com 2019-02-01T16:40:11+00:00 d76706c89adea229d2207b0280d1f3fb559671e4 Since the fsl_esdhc will also be used by SPL, make the preprocessor switches more generic to allow any kind of build. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> 
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
usb: ehci-mx6: Make regulator DM_REGULATOR dependent 2019-02-15T21:01:15+00:00 Abel Vesa abel.vesa@nxp.com 2019-02-01T16:40:08+00:00 921208ebca6f109990359b3089b5f416b269b07b Do the regulator related work only if the build has the DM_REGULATOR. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> 
Do the regulator related work only if the build has the DM_REGULATOR.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
video: bmp: Add support for 24bpp BMP files on 16bpp displays 2019-02-15T15:51:12+00:00 Stefan Roese sr@denx.de 2019-01-30T07:54:12+00:00 e25710305da0f087a374ad41d5fa1f244469f6f2 This patch adds support to load 24bpp BMP files on 16bpp displays. This will be used by the theadorable board. The "old" bmp command did support this operartion mode and to not break compatibility with the move to DM_VIDEO, we need to add this support to the "new" bmp code. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Anatolij Gustschin <agust@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de> 
This patch adds support to load 24bpp BMP files on 16bpp displays. This
will be used by the theadorable board. The "old" bmp command did support
this operartion mode and to not break compatibility with the move to
DM_VIDEO, we need to add this support to the "new" bmp code.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>