u-boot.git/drivers, branch v2019.04-rc4

Merge git://git.denx.de/u-boot-fsl-qoriq

2019-03-15T15:58:17+00:00

- DPAA2 fixes and DDR errata workaround for LS1021A

drivers: net: ls1088ardb: Fix EC1 and EC2 RCW offset

2019-03-15T06:22:01+00:00

Fix EC1 and EC2 read from correct offset 26, instead of 25

Signed-off-by: Pramod Kumar 
Acked-by: Joe Hershberger 
Reviewed-by: Prabhakar Kushwaha

mc : Reduce MC memory size to 128M

2019-03-15T06:22:00+00:00

ls2088, ls1088 : minimum MC Memory size is 128 MB
lx2 : minimum MC memory size is 256 MB

Signed-off-by: Meenakshi Aggarwal 
Acked-by: Joe Hershberger 
Reviewed-by: Prabhakar Kushwaha

driver: net: fsl-mc: Fix DPC MAC address fixup

2019-03-15T06:22:00+00:00

If node /board_info/ports does not exist in the DPC file,
function mc_fixup_dpc() will skip not only MAC address fixup,
but also the cache flush at the end. This may cause the other
fixup changes (e.g. ICID related ones) to be ignored by MC.

Fixes: 1161dbcc0a36 ("drivers: net: fsl-mc: Include MAC addr fixup to DPL")

Signed-off-by: Ioana Radulescu 
Acked-by: Joe Hershberger 
Reviewed-by: Prabhakar Kushwaha

drivers: net: ldpaa_eth: check if the dpmac is enabled

2019-03-15T06:22:00+00:00

some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.

Therefore, in fsl_rgmii_init function of SOC, we will check if the
dpmac is enabled or not? if it is (fsl_serdes_init has already enabled
the dpmac), then don't enable it.

Signed-off-by: Pankaj Bansal 
Acked-by: Joe Hershberger 
Reviewed-by: Prabhakar Kushwaha

Merge branch 'master' of git://git.denx.de/u-boot-samsung

2019-03-14T15:37:11+00:00

Merge tag 'u-boot-imx-20190313' of git://git.denx.de/u-boot-imx

2019-03-13T20:07:41+00:00

Small fixes in several i.MX boards
----------------------------------

- imx8: add pinctrl driveri (mx8m), fix documentation and
  fix reported CPU frequency. Fabio is co-maintainer
- pico-imx6ul: switch to DM
- local fixes for ventana, mx6ul_14x14_evk, engicam,
  imx6(q)_logic, liteboard

drivers/net/fec: phy_init: remove redundant logic

2019-03-13T08:14:35+00:00

The phy_connect_dev(...) function from phy.c does all the handling
(inclusive catching fixed-link).

So we drop here the single steps and call just phy_connect_dev(...).

Signed-off-by: Hannes Schmelzer 
Acked-by: Joe Hershberger

MTD: mxs_nand_spl: Redo the way nand_init initializes

2019-03-13T08:14:35+00:00

Currently the spl system calls nand_init which does nothing.
It isn't until an attempt to load from NAND that it gets initialized.
Subsequent attempts to load just skip the initialization  because
NAND is already initialized.

This moves the contents of mxs_nand_init to nand_init.  In the event
of an error, it clears the number of nand chips found.  Any
attempts to use nand will check if there are nand chips available
instead of actually doing the initialization at that time. If there
are none, it will return an error to the higher level calls.

Signed-off-by: Adam Ford

imx: serial_mxc: use CONFIG_IS_ENABLED instead of ifdef

2019-03-13T08:14:35+00:00

Kconfig allows boards to configured with DM_SERIAL and still
have SPL_DM_SERIAL disabled.  This patch changes the ifdef's
to CONFIG_IS_ENABLED to allow the modes to differ between
SPL and U-Boot.

Signed-off-by: Adam Ford 
Reviewed-by: Simon Glass