Add Cortina Access LED controller support for CAxxxx SOCs

Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Simon Glass <sjg@chromium.org>

Add head file fixed link error and remove unused flashing function
Reviewed-by: Simon Glass <sjg@chromium.org>

- XHCI updates to support MIPS better

Extend manual relocation of block_cache list pointers to all platforms that
enable CONFIG_NEEDS_MANUAL_RELOC. Remove m68k-specific checks and provide a
single implementation that adds gd->reloc_off to the pre-relocation
pointers.

Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
[trini: Add guard around DECLARE_GLOBAL_DATA_PTR to avoid size growth]
Signed-off-by: Tom Rini <trini@konsulko.com>

serial_initialize is called only during the common init sequence, after
relocation (in common/board_r.c). Because it has a void return value, it
has to wrapped in initr_serial. In order to be able to get rid of this
indirection, make serial_initialize return int.

Remove extern from prototype in order to silence the following checkpatch
warning:
check: extern prototypes should be avoided in .h files

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>

Use IS_ENABLED() instead of #ifdef in blk_post_probe function.

No functional change intended.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
[trini: Fix thinko and use CONFIG_HAVE_BLOCK_DEVICE in IS_ENABLED()]
Signed-off-by: Tom Rini <trini@konsulko.com>

Some platforms, like MIPS Octeon, use mapped addresses (virtual address
!= physical address). On these platforms we need to make sure, that the
local virtual addresses are converted to physical (DMA) addresses for
the xHCI controller. This patch adds the missing virt_to_phys() calls,
so that the correct addresses are used.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>

These values are already swapped to CPU endianess, so swapping them
again is a bug. Let's remove the swap here instead.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>

xhci_writeq() makes the CPU->LE swapping only when addressing registers
in the xHCI controller address range and not in the local memory (RAM).
We need to use cpu_to_le64() here to ensure that the conversion is done
correctly.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>

While trying to use the U-Boot xHCI driver on the MIPS Octeon platform,
which is big endian, I noticed that the driver is missing a few endian
conversion calls. This patch adds these missing endian conversion
calls.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>

Fix Kconfig entry indentation for Aspeed ast2500 pin control driver.

Fixes: 4f0e44e46615 ("aspeed: AST2500 Pinctrl Driver")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>