u-boot.git/env/Kconfig, branch v2023.01

arm64: versal-net: Add support for Versal NET platform

2022-09-26T12:23:29Z

Versal NET platform is based on Versal chip which is reusing a lot of IPs. For more information about new IPs please take a look at DT which describe currently supported devices. The patch is adding architecture and board support with soc detection algorithm. Generic setting should be very similar to Versal but it will likely diverge in longer run. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com

xilinx: Add env redund offset

2022-09-13T09:32:48Z

ENV_OFFSET_REDUND config is by default set to 0 for flashes. Saving the env variables is overwriting data at 0 offset, which is wrong. So add default redund env offset for Zynq, ZynqMP, Versal and microblaze platforms. Configured ENV_OFFSET_REDUND offsets by ENV_OFFSET + (2 * ENV_SIZE). In case of versal, we configured ENV_OFFSET_REDUND at 0x7F00000 instead of 0x7F80000. As BOOT_SCRIPT_OFFSET is already configured at 0x7F80000. Added ENV_OFFSET_REDUND in Kconfig for microblaze due to dependency of ENV_IS_IN_SPI_FLASH config. Below table specifies platform specific env and env redund offsets. PLAT ENV_OFFSET ENV_OFFSET_REDUND ---- ---------- ----------------- ZYNQ 0xE0000 0xE40000 ZYNQMP 0x1E00000 0x1E80000 VERSAL 0x7F40000 0x7F00000 MICROBLAZE 0x1080000 0x10C0000 Signed-off-by: T Karthik Reddy Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/92656dc08f0f5a749d62b71ca6e77fe1be72e9e0.1661340204.git.michal.simek@amd.com

Convert CONFIG_ENV_RANGE to Kconfig

2022-06-28T21:11:48Z

This converts the following to Kconfig: CONFIG_ENV_RANGE Now that this is in Kconfig we can enforce a minimum size and so remove the check in C code to ensure range is larger than size. Signed-off-by: Tom Rini

Convert CONFIG_ENV_MIN_ENTRIES et al to Kconfig

2022-06-28T21:11:48Z

This converts the following to Kconfig: CONFIG_ENV_MIN_ENTRIES CONFIG_ENV_MAX_ENTRIES Cc: Michal Simek Signed-off-by: Tom Rini

Convert CONFIG_ETHPRIME to Kconfig

2022-03-18T16:48:17Z

This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini

Merge tag 'v2022.04-rc4' into next

2022-03-14T21:40:36Z

Prepare v2022.04-rc4

env: sunxi: enable ENV_IS_IN_SPI_FLASH

2022-03-10T12:04:11Z

Now that sunxi uses CONFIG_SPI more sanely, and can also now properly load the environment from SPI flash, let's enable the symbol that actually considers the SPI flash when accessing the environment. As this symbol depends on CONFIG_SPI, which we now only enable if the board has a SPI flash, we can make if "default y" for all Allwinner boards. Signed-off-by: Andre Przywara Reviewed-by: Jagan Teki

env: sunxi: Define location in SPI flash

2022-03-10T12:03:23Z

To allow loading and storing the environment from SPI flash, adjust the raw offset variables for Allwinner boards to make sense there. U-Boot (including SPL and other blobs) is loaded from the beginning of SPI flash, so move the environment location as far back as possible, to not create unnecessary limits. As those offsets are shared with (now mostly unused) raw MMC environment, we should respect the common one megabyte limit, which also makes sense on SPI flash. So limit the environment for those raw locations to 64KB, and place it just below 1MB (@960KB). Those values are currently unused, unless someone forcibly enables the raw MMC environment. In this case it would break as of now, as the current offset of 544KB is far too low for the current (arm64) U-Boot proper. Signed-off-by: Andre Przywara Reviewed-by: Jagan Teki

Convert CONFIG_BOOTFILE to Kconfig

2022-03-03T21:51:20Z

This converts the following to Kconfig: CONFIG_BOOTFILE Signed-off-by: Tom Rini

Convert CONFIG_ENV_SPI_BUS et al to Kconfig

2021-12-27T13:40:33Z

This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE As part of this, we use Kconfig to provide the defaults now that were done in include/spi_flash.h. We also in some cases change from using CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in use anyhow as ENV was not enabled. Signed-off-by: Tom Rini