u-boot.git/include/asm-blackfin/global_data.h, branch master

Move architecture-specific includes to arch/$ARCH/include/asm

2010-04-13T07:13:12+00:00

This helps to clean up the include/ directory so that it only contains
non-architecture-specific headers and also matches Linux's directory
layout which many U-Boot developers are already familiar with.

Signed-off-by: Peter Tyser

Blackfin: global_data.h: make pull in needed headers

2010-01-17T14:17:26+00:00

We need the definition of bd_t in this header, so pull in asm/u-boot.h.

Signed-off-by: Mike Frysinger

Blackfin: Remove relocation fixups

2009-10-14T01:48:52+00:00

Blackfin pieces like commit 0630535e2d062dd73c1ceca5c6125c86d1127a49.

Signed-off-by: Mike Frysinger

Blackfin: change global data register from P5 to P3

2009-09-02T09:14:02+00:00

Since the Blackfin ABI favors higher scratch registers by default, use the
last scratch register (P3) for global data rather than the first (P5).
This allows the compiler's register allocator to use higher number scratch
P registers, which in turn better matches the Blackfin instruction set,
which reduces the size of U-Boot by more than 1024 bytes...

Signed-off-by: Robin Getz 
Signed-off-by: Mike Frysinger

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

Allow console input to be disabled

2008-09-06T20:36:54+00:00

Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE.

When CONFIG_DISABLE_CONSOLE is defined, setting
GD_FLG_DISABLE_CONSOLE disables all console input and output.

Signed-off-by: Mark Jackson

Change bd/gd memsize/ram_size to be phys_size_t.

2008-06-11T22:54:53+00:00

Currently, both are defined as an unsigned long, but
should be phys_size_t. This should result in no real change,
since phys_size_t is currently an unsigned long for all the
default configs.  Also add print_lnum to cmd_bdinfo to deal
with the potentially wider memsize.

Signed-off-by: Becky Bruce

POST: replace the LOGBUFF_INITIALIZED flag in gd->post_log_word (1 << 31) with the GD_FLG_LOGINIT flag in gd->flags.

2008-05-20T21:24:38+00:00

This way we become able to utilize the full post_log_word for POST
activities (overwise, POST ECC, which has 0x8000 ID, could be
erroneously treated as started in post_output_backlog() even if there
was actually no POST ECC run (because of OCM POST failure, for
example).

Signed-off-by: Yuri Tikhonov

POST: add POST_STOP flag

2008-05-20T21:24:37+00:00

Don't run futher tests in case of a test fails that is marked as
POST_STOP.

Signed-off-by: Ilya Yanok 
Signed-off-by: Yuri Tikhonov

The patch introduces the CRITICAL feature of POST tests. If the test marked as POST_CRITICAL fails then the alternative, post_critical, boot-command is used. If this command is not defined then U-Boot enters into interactive mode.

2008-03-18T21:24:48+00:00

Signed-off-by: Dmitry Rakhchev 
Signed-off-by: Yuri Tikhonov