u-boot.git/include/asm-blackfin, branch v2009.08

Blackfin: add os log functions

2009-07-19T01:15:50+00:00

Part of the mini Blackfin ABI with operating systems is that they can use
0x4f0-0x4f8 to pass log buffers to/from bootloaders.  So add support to
U-Boot for reading the log buffer.

Signed-off-by: Mike Frysinger

asm-generic: Consolidate errno.h to asm-generic/errno.h

2009-07-09T12:07:11+00:00

This patch use blackfin errno.h implementation which
correspond Linux kernel one.

MIPS implemetation is different that's why I keep it.

I removed ppc_error_no.h from Marvell boards which
was the same too.

I have got ack from ppc40x, blackfin, arm, coldfire and avr custodians.

Acked-by: Stefan Roese 
Signed-off-by: Michal Simek

Blackfin: convert specific pre/post config headers to common method

2009-06-15T00:01:13+00:00

The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup
common Blackfin board defines.  The common method now is to use config.h,
so convert blackfin-config-post.h to that.  Rename the still Blackfin
specific blackfin-config-pre.h to config-pre.h so the naming conventions
at least line up.

Signed-off-by: Mike Frysinger

Blackfin: new spibootldr command

2009-06-15T00:01:04+00:00

Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes,
so add a new 'spibootldr' command to take advantage of it.

Signed-off-by: Mike Frysinger

Blackfin: fix if() logic in bootrom evt1 check

2009-05-29T21:11:29+00:00

A missing set of parenthesis caused the silicon revision to apply only to
the BF533 and not the BF531/BF532 variants.

Signed-off-by: Mike Frysinger

Blackfin: fix booting with older bootroms (no EVT1)

2009-05-06T12:47:21+00:00

When dropping jump block support, the assumption was that all bootroms
supported entry point redirection via the EVT1 register.  Unfortunately,
this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2
and older and BF561).  No one really noticed earlier because these parts
usually are booted by bypassing the bootrom entirely, and older BF533
parts are not supported at all (too many anomalies).

Signed-off-by: Mike Frysinger

Blackfin: update anomaly sheets

2009-04-06T21:37:46+00:00

Signed-off-by: Mike Frysinger

Blackfin: force all boards to HZ of 1000

2009-04-02T10:42:26+00:00

Since the Blackfin timer code requires HZ to be 1000, barf on any board
that tries to use a different value.

Signed-off-by: Mike Frysinger

Blackfin: bf537-stamp: rewrite MAC-in-flash handling

2009-03-25T00:36:29+00:00

Use the common net eth functions to setup the env/global data with the MAC
address, and properly handle the case where CONFIG_SYS_NO_FLASH is defined.

Signed-off-by: Mike Frysinger

Blackfin: fix SIC_RVECT definition: it is 16bits, not 32bits

2009-03-23T19:14:54+00:00

Signed-off-by: Mike Frysinger