u-boot.git/include/asm-generic/global_data.h, branch v2020.04

global_data: remove unused mxc_i2c specific field

2020-01-27T06:17:53+00:00

The srdata field is unused since commit 71204e95ce13228 ("i2c: mxc:
refactor i2c driver and support dm").

Cc: Peng Fan 
Signed-off-by: Baruch Siach 
Reviewed-by: Peng Fan

global_data: Remove comment of reserved arch-specific GD flags

2019-08-18T13:54:10+00:00

With the removal of the x86 specific GD flags, there are no arch-
specific GD flags any more. Let's remove the comment about reserving the
upper 16 bits for arch-specific flags in the common header. This gives
us more flexibility with the usage of the GD flags.

As a matter of fact, we are already using more than 16 bits for common
GD flags (with the addition of GD_FLG_WDT_READY).

Signed-off-by: Stefan Roese 
Cc: Bin Meng 
Cc: Simon Glass 
Cc: Tom Rini 
Cc: Simon Goldschmidt 
Reviewed-by: Bin Meng 
Reviewed-by: Simon Goldschmidt 
Reviewed-by: Simon Glass

global_data: enable fb_base for DM_VIDEO

2019-07-30T10:54:37+00:00

with CONFIG_VIDEO we store fb base address
in global data fb_base variable. Do this
also in DM_VIDEO case.

Signed-off-by: Heiko Schocher

watchdog: Split WDT from SPL_WDT

2019-07-19T18:14:50+00:00

Use CONFIG_IS_ENABLED(WDT) to permit use of WDT in SPL without DM,
while the full U-Boot can use rich DM/DT WDT driver.

Signed-off-by: Marek Vasut 
Cc: Peng Fan 
Cc: Stefano Babic 
Tested-by: Heiko Schocher 
Tested-by: Suniel Mahesh

watchdog: Implement generic watchdog_reset() version

2019-04-26T07:16:32+00:00

This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.

Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.

With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).

This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.

Signed-off-by: Stefan Roese 
Cc: Heiko Schocher 
Cc: Tom Rini 
Cc: Michal Simek 
Cc: "Marek Behún" 
Cc: Daniel Schwierzeck 
Cc: Maxim Sloyko 
Cc: Erik van Luijk 
Cc: Ryder Lee 
Cc: Weijie Gao 
Cc: Simon Glass 
Cc: "Álvaro Fernández Rojas" 
Cc: Philippe Reynes 
Cc: Christophe Leroy 
Reviewed-by: Michal Simek 
Tested-by: Michal Simek  (on zcu100)

dm: core: Change platform specific translation-offset handling

2019-04-24T02:26:43+00:00

Testing has shown that the current DM implementation of a platform /
board specific translation offset, as its needed for the SPL on MVEBU
platforms is buggy. The translation offset is confingured too late,
after the driver bind functions are run. This may result in incorrect
address translations. With the current implementation its not possible
to configure the offset earlier, as the DM code has not run at all.

This patch now removed the set_/get_translation_offset() calls and
moves the translation offset into the GD variable translation_offset.
This variable will get used when CONFIG_TRANSLATION_OFFSET is enabled.
This option is enabled only for MVEBU on ARM32 platforms, where its
currenty needed and configured in the SPL.

Signed-off-by: Stefan Roese 
Cc: Pierre Bourdon 
Cc: Baruch Siach 
Cc: Simon Glass 
Cc: Heiko Schocher 
Cc: Tom Rini 
Tested-by: Pierre Bourdon 
Tested-by: Baruch Siach

lib: fdtdec: Add function re-setup the fdt more effeciently

2018-12-10T06:21:21+00:00

In some cases it may be useful to be able to change the fdt we have been
using and use another one instead. For example, the TI platforms uses an
EEPROM to store board information and, based on the type of board,
different dtbs are used by the SPL. When DM_I2C is used, a first dtb must
be used before the I2C is initialized and only then the final dtb can be
selected.
To speed up the process and reduce memory usage, introduce a new function
fdtdec_setup_best_match() that re-use the DTBs loaded in memory by
fdtdec_setup() to select the best match.

Signed-off-by: Jean-Jacques Hiblot 
Reviewed-by: Heiko Schocher

spl: Add support for passing handoff info to U-Boot proper

2018-11-26T13:25:37+00:00

There is some basic informaton that SPL normally wants to pass through to
U-Boot, such as the SDRAM size and bank information.

Mkae use of the new bloblist structure for this. Add a new 'handoff' blob
which is set up in SPL and passed to U-Boot proper. Also adda  test for
sandbox_spl that checks that this works correctly and a new 'sb' command
to show the information passed from SPL.

Reviewed-by: Tom Rini 
Signed-off-by: Simon Glass

bloblist: Locate bloblist in U-Boot

2018-11-26T13:25:32+00:00

Add support for locating a bloblist in U-Boot that has been set up by SPL.
It is copied into RAM during relocation.

Reviewed-by: Tom Rini 
Signed-off-by: Simon Glass

u-boot: remove driver lookup loop from env_save()

2018-07-30T11:18:47+00:00

When called with ENVOP_SAVE, env_get_location() only returns the
gd->env_load_location variable without actually checking for
the environment location and priority.

This behaviour causes env_save() to fall into an infinite loop when
the low-level drv->save() call fails.

The env_save() function should not loop through the environment
location list but it should save the environment into the location
stored in gd->env_load_location by the last env_load() call.

Signed-off-by: Nicholas Faustini 
Reviewed-by: Simon Goldschmidt