u-boot.git/include/asm-generic, branch v2014.10

dm: gpio: Enhance gpio command to show only active GPIOs

2014-09-01T05:21:06+00:00

The GPIO list is very long in many cases and most of them are not used.
By default, show only the GPIOs that are in use, and provide a flag to show
all of them. This makes the 'gpio status' command much more pleasant.

In order to do this, driver model now exposes a method for obtaining the
'function' of a GPIO, which describes whether it is an input or output, for
example. Implementation of this method is optional.

Signed-off-by: Simon Glass

Add a flag indicating when the serial console is ready

2014-07-23T13:07:25+00:00

For sandbox we have a fallback console which is used very early in
U-Boot, before serial drivers are available. Rather than try to guess
when to switch to the real console, add a flag so we can be sure. This
makes sure that sandbox can always output a panic() message, for example,
and avoids silent failure (which is very annoying in sandbox).

Signed-off-by: Simon Glass

dm: Support driver model prior to relocation

2014-07-23T13:07:24+00:00

Initialise devices marked 'pre-reloc' and make them available prior to
relocation. Note that this requires pre-reloc malloc() to be available.

Signed-off-by: Simon Glass

Add a simple malloc() implementation for pre-relocation

2014-07-23T13:05:40+00:00

If we are to have driver model before relocation we need to support some
way of calling memory allocation routines.

The standard malloc() is pretty complicated:

1. It uses some BSS memory for its state, and BSS is not available before
relocation

2. It supports algorithms for reducing memory fragmentation and improving
performace of free(). Before relocation we could happily just not support
free().

3. It includes about 4KB of code (Thumb 2) and 1KB of data. However since
this has been loaded anyway this is not really a problem.

The simplest way to support pre-relocation malloc() is to reserve an area
of memory and allocate it in increasing blocks as needed. This
implementation does this.

To enable it, you need to define the size of the malloc() pool as described
in the README. It will be located above the pre-relocation stack on
supported architectures.

Note that this implementation is only useful on machines which have some
memory available before dram_init() is called - this includes those that
do no DRAM init (like tegra) and those that do it in SPL (quite a few
boards). Enabling driver model preior to relocation for the rest of the
boards is left for a later exercise.

Signed-off-by: Simon Glass

dm: rename device struct to udevice

2014-05-27T14:21:32+00:00

using UBI and DM together leads in compiler error, as
both define a "struct device", so rename "struct device"
in include/dm/device.h to "struct udevice", as we use
linux code (MTD/UBI/UBIFS some USB code,...) and cannot
change the linux "struct device"

Signed-off-by: Heiko Schocher 
Cc: Simon Glass 
Cc: Marek Vasut

bd_info: remove bi_barudrate member from struct bd_info

2014-05-12T19:19:45+00:00

gd->bd->bi_baudrate is a copy of gd->baudrate.

Since baudrate is a common feature for all architectures,
keep gd->baudrate only.

It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.

Signed-off-by: Masahiro Yamada 
Cc: Tom Rini 
Cc: Simon Glass 
Cc: Wolfgang Denk 
Cc: Heiko Schocher 
Acked-by: Michal Simek  (For microblaze)

driver/mxc_i2c: Move static data structure to global_data

2014-04-29T05:10:27+00:00

This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.

Signed-off-by: York Sun 
CC: Troy Kisky

powerpc: remove NX823 board support

2014-04-18T14:42:29+00:00

Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/nx823/*
 - Remove include/configs/NX823.h
 - Clean-up ifdef(CONFIG_NX823)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada

powerpc: mpc8260: consolidate CONFIG_MPC8260 and CONFIG_8260

2014-03-07T15:59:06+00:00

Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.

All boards with mpc8260 cpu defined both of them:
  - CONFIG_MPC8260 was defined in board config headers
      and include/common.h
  - CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk

We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.

This commit does:
 - Delete CONFIG_8260 and CONFIG_MPC8260 definition
   in config headers and include/common.h
 - Rename CONFIG_8260 to CONFIG_MPC8260
    in arch/powerpc/cpu/mpc8260/config.mk.
 - Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260

Signed-off-by: Masahiro Yamada 
Cc: Wolfgang Denk

dm: Add GPIO support and tests

2014-03-04T17:15:30+00:00

Add driver model support for GPIOs. Since existing GPIO drivers do not use
driver model, this feature must be enabled by CONFIG_DM_GPIO. After all
GPO drivers are converted over we can perhaps remove this config.

Tests are provided for the sandbox implementation, and are a sufficient
sanity check for basic operation.

The GPIO uclass understands the concept of named banks of GPIOs, with each
GPIO device providing a single bank. Within each bank the GPIOs are numbered
using an offset from 0 to n-1. For example a bank named 'b' with 20
offsets will provide GPIOs named b0 to b19.

Anonymous GPIO banks are also supported, and are just numbered without any
prefix.

Each time a GPIO driver is added to the uclass, the GPIOs are renumbered
accordinging, so there is always a global GPIO numbering order.

Signed-off-by: Simon Glass 
Signed-off-by: Marek Vasut 
Signed-off-by: Pavel Herrmann 
Signed-off-by: Viktor Křivák 
Signed-off-by: Tomas Hlavacek