Correct GD_FLG_CYCLIC_RUNNING documentation to match Sphinx style.

Fixes: d7de5ef62935 ("cyclic: use a flag in gd->flags for recursion protection")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Currently, we must call cyclic_init() at some point before
cyclic_register() becomes possible. That turns out to be somewhat
awkward, especially with SPL, and has resulted in a watchdog callback
not being registered, thus causing the board to prematurely reset.

We already rely on gd->cyclic reliably being set to NULL by the asm
code that clears all of gd. Now that the cyclic list is a hlist, and
thus an empty list is represented by a NULL head pointer, and struct
cyclic_drv has no other members, we can just as well drop a level of
indirection and put the hlist_head directly in struct
global_data. This doesn't increase the size of struct global_data,
gets rid of an early malloc(), and generates slightly smaller code.

But primarily, this avoids having to call cyclic_init() early; the cyclic
infrastructure is simply ready to register callbacks as soon as we
enter C code.

We can still end up with schedule() being called from asm very early,
so we still need to check that gd itself has been properly initialized
[*], but once it has, gd->cyclic_list is perfectly fine to access, and
will just be an empty list.

As for cyclic_uninit(), it was never really the opposite of
cyclic_init() since it didn't free the struct cyclic_drv nor set
gd->cyclic to NULL. Rename it to cyclic_unregister_all() and use that
in test/, and also insert a call at the end of the board_init_f
sequence so that gd->cyclic_list is a fresh empty list before we enter
board_init_r().

A small piece of ugliness is that I had to add a cast in
cyclic_get_list() to silence a "discards 'volatile' qualifier"
warning, but that is completely equivalent to the existing handling of
the uclass_root_s list_head member.

[*] I'm not really sure where we guarantee that the register used for
gd contains 0 until it gets explicitly initialized, but that must be
the case, otherwise testing gd for being NULL would not make much sense.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mm-venice-*

As a preparation for future patches, use a flag in gd->flags rather
than a separate member in (the singleton) struct cyclic_drv to keep
track of whether we're already inside cyclic_run().

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mm-venice-*

Now that all the old code is gone, rename this option. Driver model
migration is now complete.

Signed-off-by: Simon Glass <sjg@chromium.org>

These rely on the old LCD implementation which is to be removed. Drop it
all.

Signed-off-by: Simon Glass <sjg@chromium.org>

If the device tree changes during a test and we cannot restore it, mark
it as such so that future tests which need the live tree are skipped.

Signed-off-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Tom Rini <trini@konsulko.com>

This allows to test if a pin's label if displayed using gpio_get_status()
when this pin is configured in alternate function.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Add the basic infrastructure to periodically execute code, e.g. all
100ms. Examples for such functions might be LED blinking etc. The
functions that are hooked into this cyclic list should be small timewise
as otherwise the execution of the other code that relies on a high
frequent polling (e.g. UART rx char ready check) might be delayed too
much. This patch also adds the Kconfig option
CONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time
for such a cyclic function. If it's execution time exceeds this time,
this cyclic function will get removed from the cyclic list.

How is this cyclic functionality executed?
The following patch integrates the main function responsible for
calling all registered cyclic functions cyclic_run() into the
common WATCHDOG_RESET macro. This guarantees that cyclic_run() is
executed very often, which is necessary for the cyclic functions to
get scheduled and executed at their configured periods.

This cyclic infrastructure will be used by a board specific function on
the NIC23 MIPS Octeon board, which needs to check periodically, if a
PCIe FLR has occurred.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

I do not have any non-serial output devices, so a
print_pre_console_buffer(PRE_CONSOLE_FLUSHPOINT2_EVERYTHING_BUT_SERIAL)
does nothing for me.

However, I was manually inspected the pre-console buffer using md.b,
and I noticed that the early part of it was repeated. The reason is
that the first call of print_pre_console_buffer(), from
console_init_f(), ends up invoking puts() with the contents of the
buffer at that point, and puts() at that point ends up in the else
branch of

	if (gd->flags & GD_FLG_DEVINIT) {
		/* Send to the standard output */
		fputs(stdout, s);
	} else {
		/* Send directly to the handler */
		pre_console_puts(s);
		serial_puts(s);
	}

so indeed the contents is added again.

That can be somewhat confusing (both when reading the buffer manually,
but also if it did actually come out on some device). So disable all
use of the pre-console buffer while print_pre_console_buffer() is
emitting it.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>