u-boot.git/include/ata.h, branch v2017.01

Properly calculate ATA_SECTORWORDS, using a fixed-size integer, so it works for both 32-bit and 64-bit targets

2016-05-20T23:25:50+00:00

Signed-off-by: Stanislav Galabov

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38+00:00

Signed-off-by: Wolfgang Denk 
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini

ahci: Perform SATA flush after disk write.

2012-11-02T22:20:43+00:00

Writes in u-boot are so rare, and the logic to know when is
the last write and do a flush only there is sufficiently
difficult. Just do a flush after every write. This incurs,
usually, one extra flush when the rare writes do happen.

Signed-off-by: Marc Jones 
Signed-off-by: Simon Glass

CPCI750: Add CPCI-HD/2 support

2012-03-18T19:10:02+00:00

This patch adds support for the esd CPCI-HD/2 board to u-boot for CPCI-CPU/750.
As the primary devices on the CPCI-HD/2 board are connected to device 1 and 3,
the device must be swapped.

Signed-off-by: Reinhard Arlt

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

Add a hook to allow board-specific PIO mode setting.

2008-08-20T23:31:04+00:00

This patch adds a hook whereby a board-specific routine can be called to
configure hardware for a PIO mode.  The prototype for the board-specific
routine is:

	int inline ide_set_piomode(int pio_mode)

ide_set_piomode should be prepared to configure hardware for a pio_mode
between 0 and 6, inclusive.  It should return 0 on success or 1 on failure.

Signed-off-by: Steven A. Falco

Replace enums in ata.h with an include of libata.h

2008-08-20T23:20:45+00:00

This patch removes some enums from ata.h and replaces them with an
include of libata.h.  This way, we eliminate duplicated code, and
prevent errors whereby the different versions could be out of sync.

Signed-off-by: Steven A. Falco

Minor coding style cleanup.

2007-05-15T21:38:05+00:00

Add driver for S-ATA-controller on Intel processors with South

2007-05-15T21:25:37+00:00

Bridge, ICH-5, ICH-6 and ICH-7. 

Implementation:

1. Code is divided in to two files. All functions, which are
   controller specific are kept in "drivers/ata_piix.c" file and
   functions, which are not controller specific, are kept in
   "common/cmd_sata.c" file.

2. Reading and Writing from the S-ATA drive is done using PIO method.

3. Driver can be configured for 48-bit addressing by defining macro
   CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
   addressing.

4. S-ATA read function is hooked to the File system, commands like
   ext2ls and ext2load file can be used. This has been tested.

5. U-Boot command "SATA_init" is added, which initializes the S-ATA
   controller and identifies the S-ATA drives connected to it.

6. U-Boot command "sata" is added, which is used to read/write, print
   partition table and get info about the drives present. This I have
   implemented in same way as "ide" command is implemented in U-Boot.

7. This driver is for S-ATA in native mode.

8. This driver does not support the Native command queuing and
   Hot-plugging.

Signed-off-by: Mushtaq Khan

Code cleanup; make several boards compile & link.

2004-03-14T22:25:36+00:00