u-boot.git/include/common.h, branch v2014.10

common.h: remove MIN, MAX, MIN3, MAX3 macros

2014-09-24T22:30:29+00:00

Now MIN, MAX, MIN3, MAX are not used.
Going forward, use min, max, min3, max3.

Signed-off-by: Masahiro Yamada

arm:reset: call the reset_misc() before the cpu reset

2014-09-05T04:58:49+00:00

On an Odroid U3 board, the SOC is unable to reset the eMMC card
in the DWMMC mode by the cpu software reset. Manual reset of the card
by switching proper gpio pin - fixes this issue.

Such solution needs to add a call to pre reset function.
This is done by the reset_misc() function, which is called before reset_cpu().
The function reset_misc() is a weak function.

Signed-off-by: Przemyslaw Marczak 
Cc: Minkyu Kang 
Cc: Jean-Christophe PLAGNIOL-VILLARD 
Cc: Albert ARIBAUD 
Cc: Tom Rini 

Changes v4:
- arch/arm/reset: fix weak function attribute to proper style
Signed-off-by: Minkyu Kang

powerpc: mpc8xx: remove stxxtc board support

2014-08-21T16:01:12+00:00

This board has been orphaned for a while and old enough.

Signed-off-by: Masahiro Yamada

ARM: convert arch_fixup_memory_node to a generic FDT fixup function

2014-07-28T15:19:49+00:00

Some architecture needs extra device tree setup. Instead of adding
yet another hook, convert arch_fixup_memory_node to be a generic
FDT fixup function.

[maz: collapsed 3 patches into one, rewrote commit message]

Signed-off-by: Ma Haijun 
Signed-off-by: Marc Zyngier 
Acked-by: Ian Campbell

stdio: Pass device pointer to stdio methods

2014-07-23T13:07:23+00:00

At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.

For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.

Instead, add a stdio_dev pointer to each of the stdio member functions.

Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.

Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.

22: stdio: Pass device pointer to stdio methods
       arm: (for 2/2 boards)  all +244.0  bss -4.0  text +248.0
   powerpc: (for 1/1 boards)  all +428.0  text +428.0

Signed-off-by: Simon Glass 
Acked-by: Marek Vasut 
Reviewed-by: Marek Vasut

mpc8xx: remove fads board support

2014-07-07T23:43:02+00:00

These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada

mpc8xx: remove RPXlite_dw, quantum board support

2014-07-07T23:43:01+00:00

These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada

ARMv8/FSL_LSCH3: Add FSL_LSCH3 SoC

2014-07-03T06:40:51+00:00

Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.

Signed-off-by: York Sun 
Signed-off-by: Varun Sethi 
Signed-off-by: Arnab Basu

Add run_command_repeatable()

2014-06-11T20:25:47+00:00

run_command() returns 0 on success and 1 on error. However, there are some
invocations which expect 0 or 1 for success (not repeatable or repeatable)
and -1 for error; add run_command_repeatable() for this purpose.

Signed-off-by: Thomas Betker 
Acked-by: Simon Glass 
Tested-by: Simon Glass

powerpc: ep8248: remove orphan board

2014-05-30T18:03:24+00:00

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada 
Cc: Wolfgang Denx