u-boot.git/include/configs/P1010RDB.h, branch master

PowerPC / Layerscape: Finish migration to DM_SERIAL

2025-05-30T16:16:51+00:00

Migrate the few ARM Layerscape platforms that had not been switched
along with all remaining PowerPC platforms to DM_SERIAL. For PowerPC,
this means that platforms which use SPL/TPL, keeping the non-DM serial
driver enabled there as they do not use DM. We also rework the guards
on how to define CFG_SYS_NS16550_CLK so that this is mostly in one place
now.

Signed-off-by: Tom Rini

include: Use CONFIG_XPL_BUILD instead of CONFIG_SPL_BUILD

2024-10-11T17:44:48+00:00

Use the new symbol to refer to any 'SPL' build, including TPL and VPL

Signed-off-by: Simon Glass

global: Migrate CONFIG_RESET_VECTOR_ADDRESS to CFG

2022-12-23T15:15:11+00:00

Perform a simple rename of CONFIG_RESET_VECTOR_ADDRESS to CFG_RESET_VECTOR_ADDRESS

Signed-off-by: Tom Rini

global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFG

2022-12-23T15:09:42+00:00

Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS

Signed-off-by: Tom Rini

global: Remove undef CONFIG_... for unused values

2022-12-23T15:07:03+00:00

We have a number of places that undef CONFIG_... while we never
reference CONFIG_... in the first place. Remove these lines.

Signed-off-by: Tom Rini

ddr: fsl: Remove CONFIG_MEM_INIT_VALUE

2022-12-22T15:31:48+00:00

The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.

Signed-off-by: Tom Rini

Convert CONFIG_L2_CACHE to Kconfig

2022-12-22T15:31:48+00:00

This converts the following to Kconfig:
   CONFIG_L2_CACHE

Signed-off-by: Tom Rini

global: Remove unused CONFIG symbols

2022-12-22T15:31:48+00:00

This removes the following unreferenced CONFIG symbols:
   CONFIG_FDTADDR
   CONFIG_FDTFILE
   CONFIG_FLASH_SECTOR_SIZE
   CONFIG_FSL_CPLD
   CONFIG_HDMI_ENCODER_I2C_ADDR
   CONFIG_I2C_MVTWSI
   CONFIG_I2C_RTC_ADDR
   CONFIG_IRAM_END
   CONFIG_IRAM_SIZE
   CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
   CONFIG_L1_INIT_RAM
   CONFIG_MACB_SEARCH_PHY
   CONFIG_MIU_2BIT_21_7_INTERLEAVED
   CONFIG_MTD_NAND_VERIFY_WRITE
   CONFIG_MVGBE_PORTS
   CONFIG_NETDEV
   CONFIG_NUM_DSP_CPUS
   CONFIG_PHY_BASE_ADR
   CONFIG_PHY_INTERFACE_MODE
   CONFIG_PSRAM_SCFG
   CONFIG_RAMBOOT_SPIFLASH
   CONFIG_RAMBOOT_TEXT_BASE
   CONFIG_RD_LVL
   CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
   CONFIG_SETUP_INITRD_TAG
   CONFIG_SH_QSPI_BASE
   CONFIG_SMDK5420
   CONFIG_SOCRATES
   CONFIG_SPI_ADDR
   CONFIG_SPI_FLASH_QUAD
   CONFIG_SPI_FLASH_SIZE
   CONFIG_SPI_HALF_DUPLEX
   CONFIG_SPI_N25Q256A_RESET
   CONFIG_TEGRA_SLINK_CTRLS
   CONFIG_TPM_TIS_BASE_ADDRESS
   CONFIG_UBOOT_SECTOR_COUNT
   CONFIG_UBOOT_SECTOR_START
   CONFIG_VAR_SIZE_SPL
   CONFIG_VERY_BIG_RAM

And also:
   BL1_SIZE
   PHY_NO
   RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini

Convert CONFIG_HOSTNAME et al to Kconfig

2022-12-22T15:31:48+00:00

This converts the following to Kconfig:
   CONFIG_GATEWAYIP
   CONFIG_HOSTNAME
   CONFIG_IPADDR
   CONFIG_NETMASK
   CONFIG_ROOTPATH
   CONFIG_SERVERIP
   CONFIG_UBOOTPATH

To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.

Signed-off-by: Tom Rini

Convert CONFIG_FLASH_SHOW_PROGRESS to Kconfig

2022-12-22T15:31:48+00:00

This converts the following to Kconfig:
   CONFIG_FLASH_SHOW_PROGRESS

Signed-off-by: Tom Rini