u-boot.git/include/configs/afeb9260.h, branch master

ARM: at91: remove non-generic boards

2015-05-13T11:01:25+00:00

Remove board support for afeb9260, tny_a9260, and sbc35_a9g20.

They have not been converted into Generic Board yet.
See doc/README.generic-board for details.

Signed-off-by: Masahiro Yamada 
Cc: Sergey Lapin 
Cc: Albin Tonnerre 
Cc: Andreas Bießmann

spi, atmel: move CONFIG_SYS_SPI_WRITE_TOUT into common header

2014-11-17T13:47:16+00:00

move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).

Signed-off-by: Heiko Schocher 
Reviewed-by: Jagannadha Sutradharudu Teki 
Reviewed-by: Andreas Bießmann 
Signed-off-by: Andreas Bießmann

arm926ejs, at91: add common phy_reset function

2013-12-01T21:38:52+00:00

add common phy reset code into a common function.

Signed-off-by: Heiko Schocher 
Cc: Andreas Bießmann 
Cc: Bo Shen 
Cc: Jens Scharsig 
Cc: Sergey Lapin 
Cc: Stelian Pop 
Cc: Albin Tonnerre 
Cc: Eric Benard 
Cc: Markus Hubig 
Acked-by: Jens Scharsig (BuS Elektronik) 
Tested-by: Jens Scharsig (BuS Elektronik) 
Tested-by: Bo Shen 
Acked-by: Bo Shen 
Signed-off-by: Andreas Bießmann

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

2013-11-09T21:59:47+00:00

Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h

arm: atmel: get rid of too many ifdeffery

2013-11-04T19:32:37+00:00

Get rid of too many ifdeffery in usb ohci driver

Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock

Signed-off-by: Bo Shen 
Signed-off-by: Andreas Bießmann

config: remove platform CONFIG_SYS_HZ definition part 2/2

2013-11-04T16:06:16+00:00

Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38+00:00

Signed-off-by: Wolfgang Denk 
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini

ARM: Remove unused stack and irq config defines

2012-09-01T12:58:22+00:00

CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.

IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.

Cc: Albert ARIBAUD 
Signed-off-by: Rob Herring

CONFIG_SYS_BAUDRATE_TABLE: Add , place there

2012-06-20T18:26:16+00:00

We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in  which mkconfig places after  in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini

board configs: drop NET_MULTI references

2011-10-05T20:22:16+00:00

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger